Category: STARTER KITS, PROGRAMMERS, MODULES
Kamami.pl electronics store offers a wide range of starter kits for microcontrollers and programmable devices as well as accessories (programmers, modules, etc.).
Subcategories
-
Atmel SAM
-
Atmel Xplain
-
AVR
-
DFRobot FireBeetle
-
ESP32
-
ESP8266
-
Feather / Thing Plus
-
Freedom (Kinetis)
-
Coral
-
Nordic nRF
-
M5Stack
-
Micro:bit
-
Peripheral modules
-
Particle Photon
-
PIC
-
Segger programmers
-
Universal programmers
-
Raspberry Pi RP2040
-
RFID
-
RISC-V
-
Seeed Studio LinkIt
-
Sparkfun MicroMod
-
STM32
-
STM32 MP1
-
STM32 Discovery
-
STM32 Nucleo boards
-
STM8
-
Teensy
-
WRTNode
-
XIAO/Qt PY
-
Other development kits
-
SOFTWARE
There are 2402 products.
The ESP32 WiFi and Bluetooth module has a dual-core 32-bit MCU that integrates WiFi HT40 and Bluetooth / BLE 4.2 technology. Designed for mobile devices and Internet of Things (IoT) applications. DFRobot TEL0111
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
STM32 Nucleo-32 development board with STM32F042K6T6 MCU, supports Arduino connectivity
Earth humidity sensor with analogue output, supplied with 3.3 to 5.5 V voltage with Gravity connector. DFRobot SEN0193
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
A small module with a PIR motion sensor. It allows detecting movement within a maximum range of 6 meters (default up to 3 meters). The measuring angle is 120 degrees. The module has a connector in accordance with the Grove standard. Seeed Studio 101020020
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078
The STEVAL-MKI079V1 board enables demonstration and testing of the dual-axis LPR430AL gyroscope in analog or digital mode. The built-in microcontroller and USB interface facilitate signal analysis and the development of MEMS sensor-based applications in measurement and control systems.
Adafruit 1088
Adafruit 603 - Stainless Thin Conductive Yarn / Thick Conductive Thread - 35 ft
Bright white SMD 3528 LED module. DFRobot DFR0438
Dreamer Nano V4 - Arduino Leonardo compatible; ATmega 32U4
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
This V2 Rotation Sensor is arduino compatible multi-ring rotation sensor. It is based on multi-turn precision potentiometer. It can rotate upto 10 laps. DFR0058
The liquid flow sensor is made of a plastic body, a flow rotor and a Hall sensor. DFRobot SEN0217
Module with MLX90614-DCC sensor for non-contact temperature measurement in the range from -70℃ to 380℃. I2C communication. DFRobot SEN0206