zł173.42 tax excl.
NFC module with built-in antenna on the board. The module has a Gravity connector. Memory communication can be done through one of the serial interfaces: UART or I2C. DFRobot DFR0231-H
NFC module based on the NXP PN532 chip with built-in antenna on the board. The module has a Gravity connector for connecting the device to the most popular development kits such as Arduino or micro:bit. Memory communication can be done through one of the serial interfaces: UART or I2C. Thanks to the dual interface, the module can work with both microcontrollers and PCs via a USB-UART converter.
Near Field Communication (NFC), also known as short-range wireless communication, is a short-range wireless communication technology that allows contactless point-to-point data transmission (at a distance of ten centimeters) to exchange data between electronic devices.
Example connection



Manufacturer
Responsible person
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
No product available!
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
Gravity: Digital IR Receiver Module is a module with an IR receiver operating at 38kHz. The module is supplied with 5V voltage. DFRobot DFR0094
Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440
Gravity: Digital Capacitive Touch Sensor is a capacitive touch sensor powered by 3.3V ... 5V voltage. DFRobot DFR0030
Gravity: Digital Crash sensor is a microswitch module (left) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-L
Gravity: Digital Crash sensor is a microswitch module (right) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-R
Module with an IR transmitter operating at a frequency of 38kHz. The module is supplied with the voltage from 3 to 5V. FRobot DFR0095
No product available!
Gravity sensor adapter with 3-pin terminal connector. There are two 10 kΩ pull-up and pull down resistors on the board, set with a jumper. DFRobot DFR0055
Module with blue LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-B
Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-R
Module with white LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-W
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
No product available!
Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563
2x16 character LCD display. It can display the font in any color from the RGB palette. Communication via the I2C interface. The module has a lead compliant with the Gravity standard. DFRobot DFR0554
No product available!
NFC module with built-in antenna on the board. The module has a Gravity connector. Memory communication can be done through one of the serial interfaces: UART or I2C. DFRobot DFR0231-H