Touch button with green LED backlight. Powered with the voltage in the range from 2.7 V to 6 V, it works with 3.3 V systems

Real time clock (RTC) module DS1307. It is powered by 5 V and communicates via the I2C interface (Gravity connector). There is also a CR1220 battery socket on the board. DFRobot DFR0151

XT30U connector set (male plug and female socket) with a maximum forward current of 30 A. It works well as a battery connector or a power connector in RC models. Amass XT30U

GOODRAM CX400 gen. 2 SSD with a capacity of 256 GB. It is equipped with a SATA III interface, has a 2.5" format. Goodram SSDPR-CX400-256-G2

GOODRAM CX400 gen. 2 SSD with a capacity of 128 GB. It is equipped with a SATA III interface, has a 2.5" format. Goodram SSDPR-CX400-128-G2

The Texas Instruments H-bridge allows control of two DC brush motors or one stepper motor. The supply voltage of the motor is in the range of 0-11V, maximum current efficiency 1.5A / bridge. The system has a 12WSON housing

A small USB 2.0 hub that allows you to disable individual devices connected to its USB ports, as well as a visual evaluation of the number of devices enabled. It has a built-in connector for the external power supply, so it can act as an active hub. Cable with a length of 40cm, 4 USB ports

XT60E-M connector (male plug) with a maximum conductive current of 60 A. Equipped with mounting holes, it will work as a battery connector or a power connector in RC models. Amass XT60E-M

Tilt Sensor

A set of goldpin connectors and contacts with a pitch of 2.54 mm. The set includes 1550 elements. Everything is closed in a handy organizer

SEN-13582

8x8 pixel LED matrix display with red LEDs. The module is equipped with the 74HC595 controller and communicates via the I2C interface

SPDT momentary switch. It enables stable switching between two signal states with a voltage of 250 V AC and 3 A

Wireless PS2 controller included with the receiver. It has a range of approx. 8 m and is powered by two AAA batteries. Communication via the SPI interface

INEMO system: 3D accelerometer and 3D gyroscope in LGA16L housing, made by STMicroelectronics. Allows measurement of acceleration up to 16g and angular velocity up to 2000 degrees / second, communication takes place on the I2C / SPI bus

The Microchip system in the DIP8 housing, a dual driver, allows the MOSFET transistors to be controlled with a high switching speed. The controller is characterized by low power consumption, high current efficiency when loading eg gate capacity, or ESD resistance up to 4kV

The shield provides the standard MIDI port circuits, incl. 5-pin DIN connectors, pto-isolated MIDI input, LEDs on D6 and D7, pushbuttons on D2, D3 and D4, and rotary potentiometers on A0 and A1. DEV-12898

The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I²C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.. Digilent 410-287

Module with 12-position rotary switch. It is supplied with the voltage ranging from 3.3 V to 12 V and has an analog output (Gravity connector). DFRobot SEN0156

16-channel GPIO expander with an I2C interface microcontroller can interface with 16 fully configurable digital input/output pins. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. With a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix. BOB-13601