ToF distance sensor module based on the VL53L1X system. It offers a range from 4 to 400 cm and communicates via the I2C, UART or Modbus interface. TOF400F

I2C FRAM breakout board you can add some FRAM storage to your next DIY project. FRAM allows for a lower power usage and a faster write performance. Adafruit 1895

BMI270 3-axis accelerometer and gyroscope module. The chip is a low-power IMU optimised for wearables, providing precise acceleration measurement, angular velocity measurement and motion-triggered interrupt functions. Equipped with a Qwiic connector, it communicates via an I2C interface. SparkFun SEN-22398

Small LED matrix display with built-in rechargeable battery. Programmable via USB and Windows PC or Bluetooth and iOS and Android applications

A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2980

The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while allowing for a maximum output current of 500 mA. Pololu 2844

Module with analogue UV light sensor ML8511. It enables the measurement of the radiation intensity for the UV-A (320-400nm) and UV-B (280-320nm) waves. It has an analog interface. GY8511

RGB LED driver module equipped with ATtiny1616 microcontroller and STEMMA QT connector. It uses a 3.3V/5V voltage level converter and allows you to control the popular Neopixel LEDs. Adafruit 5766

The 6-55V 200W Step-Up Converter Module is a device that converts a DC input voltage (6-35V) to a higher DC output voltage (6-55V) with a maximum input power of 200W, a maximum input current of 10A and a maximum output current of 7A. It offers a high conversion efficiency of up to 97.6% and it is recommended to keep a margin when operating for long periods to avoid overheating.

Adapter for RFID reader (125 kHz). Works with ID-3LA, ID-12LA and ID-20LA series systems. SparkFun SEN-13030

Pololu 4817 is a set of two JST SH 5-pin side-entry adapters that allow easy connection of JST SH wires to breadboards and prototype boards. Thanks to the side-entry wire insertion, the adapters are particularly useful in compact designs and projects requiring neat cable routing.

Two-channel driver of direct current (DC) motors with an operating voltage from 6 to 30 V and a maximum continuous current of 20 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD20A

Module with digital light intensity sensor MAX44009. It is supplied with the voltage from 1.7 to 3.6 V and communicates via the I2C interface. GY-49

Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396

Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR

Wide angle lens with CS-Mount. Focal length 6 mm, FoV 65°, manual focus and adjustable aperture. Designed to work with the Raspberry Pi HQ camera. ArduCAM LN037

Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B

The Kruger & Matz HDMI / HDMI (AA) cable is used to transfer video and audio. Allows you to connect DVD and Blu-Ray players to a TV or monitor. KM0329

Switch module with a maximum voltage of 12 V and a current of 10 A based on a MOSFET transistor, controlled by a digital pin. It is equipped with a screw connection and a status LED. SparkFun SPX-19799