IPS LCD display 7" with a resolution of 1024x600 px with a touch panel. It uses the eDP interface and is compatible with LattePanda Alpha and Delta. DFRobot FIT0551

A power module for the Pimoroni Yukon platform that allows independent control of two high-current outputs within a voltage range of 5 to 17 V. Built-in diodes and chokes enable excellent handling of inductive loads such as pumps, fans, and solenoids. Each channel can also operate in PWM mode, allowing for smooth power regulation in slow-response devices. The module supports a total current of up to 15 A and includes temperature sensors and a "power good" signal. Pimoroni PIM692

Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595

3D camera module with ToF technology and the ability to record images in RGB color with a resolution of 320 x 240 pixels. Additionally, it is equipped with an IMU measurement system. The camera enables easy acquisition of RGB-D data via a USB cable and, when combined with a web interface, enables viewing of depth maps, point cloud data, and rendering of colored 3D objects in real time. DFRobot SEN0583

The 3D TOF camera is a module that consists of the BL702 system and the Juyou 100x100 TOF sensor. It is a 3D sensor that allows you to measure distances up to 1.5 meters. It is equipped with a 1.14-inch LCD screen that allows real-time viewing of depth maps along with color maps. DFRobot SEN0581

Female terminal block, 4-pin. Pitch 3.81mm. Height 11.1mm. 15EDGK-3.81-4P. Set of 5 pieces

A set of necessary tools needed to perform vehicle diagnostics. It consists of a CAN Bus module, an OBD II connector and the necessary wires. Seeed Studio 114991438

(DRI0009) 2A Motor Shield For Arduino

IPS LCD display with a screen diagonal of 11.9". It offers a resolution of 320 x 1480 pixels and an HDMI input, which allows you to easily connect the display to various signal sources. Waveshare 11.9inch Side Monitor

Module with SHT35 temperature and humidity sensor. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020592

Module with BDS/GNSS AT6558 receiver. It can receive data from six location systems simultaneously: GPS, GLONASS, Galileo, QZSS, SBAS and BeiDou. It communicates via the UART interface. DFRobot TEL0132

7-segment LED display, 1 13.20mm digit, bright green (575nm), 25mcd (10mA), common anode, Pb-free. LED1-AS-B-05211BUMG

Low Energy Bluetooth adapter module with USB 2.0 connector. allows communication with BLE devices

A 15.6" QLED display with touch panel. It is equipped with a mini HDMI interface for video display and USB Type C for the touchscreen. It offers a resolution of 1920 x 1080 pixels. Waveshare 15.6inch QLED Monitor (EU)

ACeP e-Paper 7-color display with a diagonal of 5.65" and a resolution of 600×448 px. SPI interface. Without PCB. Waveshare 5.65inch e-Paper (F)

This is a little 5" TFT display with WVGA 800x480 resolution and it has a resistive touchscreen overlay. The driver board only has an HDMI input but for Raspberry Pi, BeagleBone Black and other computers. Adafruit 2109

2.8" display with 320x240 16-bit color pixels and a capacitive touch overlay fits perfectly onto the Raspberry Pi 3/2/A+/B+. The display and touchscreen uses the hardware I2C Pins (SDA & SCL), SPI pins (SCK, MOSI, MISO, CE0) as well as GPIO #25 and #24. Adafruit 2423