Zynq-7000 All Programmable SoC, Dual ARM Cortex-A9 MPCore, Artix-7 FPGA, 85K Logic Cells, 256KB, 766MHz, CSPBGA484, Xilinx

RT8289GSP, 5A, 32V, 500kHz Step-Down Converter, SOP-8

Radio module with 868 MHz operating frequency. Communication takes place via the UART serial interface. It is supplied with the voltage in the range from 3.4 to 5.5 V. DFRobot TEL0115

LoRa radio module with 433 MHz operating frequency. Communication takes place via the UART serial interface. It is supplied with the voltage in the range from 3.4 to 5.5 V. DFRobot TEL0116

Set with a measuring module and a probe for measuring the pH of wet soil and food products. The module is powered with the voltage of 5 V and has an analog output with a voltage range from 0 to 4 V. DFRobot SEN0249

The module with the SX127x 433 MHz system for LoRa communication, designed for FireBeetle boards. It communicates via the SPI interface. DFRobot TEL0121

Module with an analog sound intensity sensor. It enables measurement in the range from 30 dB to 130 dB with a measurement error of ± 1.5 dB. The module returns the output voltage in the range of 0.6 to 2.6 V. DFRobot SEN0232

Gravity: Analog TDS Sensor / Meter is an analog water purity measurement module. It is powered by 3.3 ... 5.5V voltage and has an analogue output interface. Module compatible with Arduino. DFRobot SEN0244

Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492

El-wire is a thin and flexible wire which shines under high voltage. The cable is light blue (CYAN), has a diameter of 3mm and a length of 3 meters

Round, flexible, pressure sensor that can be used to implement very sensitive force detection. The sensor is durable and designed to detect static and dynamic pressure at high response speeds. DFRobot SEN0295

3-color e-Paper display with a diagonal of 12.48" and a resolution of 1304x984 px. SPI interface. Without PCB. Waveshare 12.48inch e-paper (B)

Numeric keypad module with 12 buttons. The board has the ATtiny85 microcontroller, which processes data from the keyboard and sends it in a convenient form via the I2C interface. SparkFun COM-15290

Flexible extension for a microSD card with a length of 25 cm. Supports all capacities and card types, including: 16 GB, 32 GB, 64 GB, 128 GB Micro SD/SDHC.

Red laser diode module with 5mW power, displaying intersecting lines. Ideally suited to the construction of the laser level, and thanks to the built-in driver, it is possible to power 3 - 5V. LD-G650A03 - Cross

The ring has sixteen RGB WS2812 diodes, controlled by means of serial signals. The module can be supplied with voltage from 4-7V, only one signal line is required to control it. NeoPixel Ring 16 x WS2812

Module with bipolar stepper motor driver TC78H670FTG. It allows you to control the motor with an accuracy of 1/128 of a step with a voltage from 3.6 to 16 V and a current of up to 2 A. SparkFun ROB-16836

JST-SH 4-pin SMD connector for modules with Qwiic connectors. Pins\' pitch is 1 mm. Qwiic allows you to connect sensors via the I2C bus. SparkFun PRT-16766

Module with 2-channel DC motor driver. It allows you to control the drive with a supply voltage from 3 to 11 V and a current of 1.2 A (1.5 A instantaneous). I2C communication. SparkFun ROB-15451