The Zeenko 20 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.

High-voltage oscilloscope probe with BNC connector and 100:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 2 kV. Hantek T3100

6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.0mm

6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.5mm

Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT20COP

A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201

The Hantek PP-300 is an oscilloscope probe with a bandwidth of 300 MHz, designed for precise measurement of high-frequency signals. It is compatible with a wide range of digital and analog oscilloscopes and features a switchable attenuation setting between 1× and 10×, allowing flexible adaptation to various applications. Thanks to its ergonomic design and robust construction, the probe offers user comfort and durability for everyday use in laboratory environments.

Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.

Oscilloscope Probes (pair). 460-004

This active measurement probe is designed for precise analysis of ripple, noise, and rapid changes on DC power lines, particularly in systems requiring high power integrity. The device offers a bandwidth of up to 2 GHz and a wide operating range, enabling accurate measurements of very small amplitude signals with minimal load on the system under test. With an SMA interface, 5V USB-C power supply, and a low current consumption of 20 mA, the probe easily integrates with test benches and oscilloscopes. PRP1 Power Rail Probe v2.0

Protective handbag designed for Micsig oscilloscopes of the TO, ATO and STO series.

A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650

High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050

BNC connector cable (adapter) to the "Alligator clip" connector. It allows you to conveniently connect the device, e.g. to an oscilloscope. Digilent (240-134)

Probe for measuring direct current up to 800 A and alternating current up to 500 A. Operates at 5 kHz and can be connected to an oscilloscope via a BNC connector. Powered via USB. Hantek CC-800

BNC connector adapter cable for mini-grabber clips. Connects to Analog Discovery 2 via a BNC adapter. Digilent 240-136

An oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Micsig MS-A-008

The P2150 oscilloscope probe with a 150 MHz bandwidth and BNC connector ensures high signal integrity and wide bandwidth, featuring switchable attenuation of 1X/10X and an input resistance of 1 MΩ/10 MΩ ±2%. The set includes accessories such as a compensation tool, identification rings, and a hook clip for easier use.

Universal measurement probes for a multimeter. Compatible with all Micsig oscilloscopes. Micsig MS-A-005