Category: Main categories

AVR PDI adapter from standard 2.54mm 20 pin connector to 2.54mm 6 pin, 1.27mm 6 pin or 2.54mm 10 pin AVR PDI connector. Segger AVR PDI Adapter (8.06.26)

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at a frequency of 133 MHz, 264 kB RAM. There is as much as 16 MB of QSPI flash memory on the board. The system can be programmed in C / C ++ or microPython. KApico RP2040

The Raspberry RPI-ENC054-BK enclosure is a black aluminum case compatible with the Raspberry Pi 4B, providing solid protection and passive cooling. Thanks to the VESA mount, it allows convenient installation, for example behind a monitor, while precise cutouts ensure full access to all connectors.

Development board with ESP-WROOM-32 module. It allows communication within the WiFi network and the Bluetooth 4.2 (BLE) standard

A cryptography kit that allows you to learn the basics of cryptographic authentication and the ATECC508A cryptographic co-processor. SparkFun KIT-18303

Set with OpenLog Artemis data logger. The set includes an I2C expander, a strain gauge module, a USB type C cable, a 1250 mAh LiPo battery, a 1 GB microSD card and all the necessary Qwiic cables. SparkFun KIT-18295

The module is equipped with the LTE-M/NB-IoT u-blox SARA-R510M8S system. It allows you to monitor devices remotely. SparkFun GPS-18031

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)

Adapter that converts standard 20-pin 2.54 mm connector to SWIM connector and 10-pin connector. Used for programming STM8 chips. Segger STM8 Adapter (8.06.22)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

Adapter from the standard 20-pin 2.54 mm connector to the 10-pin 1.27 mm connector often used in Cortex-M boards. Segger 50-Mil 10-Pin Patch Adapter (8.06.28)

A set of three copper heat sinks. Equipped with an adhesive tape for easy installation

Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)

A set for building a minicomputer based on Raspberry Pi CM4. It consists of a metal case with a fan, a power supply and a Dual Gigabit Ethernet Base Board. Waveshare CM4-DUAL-ETH-BOX-A-EU

Base board dedicated to Raspberry Pi CM4 modules. It is equipped with two RJ45 connectors, three USB 3.2, HDMI, DSI and CSI. Additionally, the board has an RTC system and a fan connector. Waveshare CM4-DUAL-ETH-BASE

Air quality sensor module based on the SGP40 system. It uses CMOSens® technology by Sensirion and provides information on air quality. Waveshare SGP40 VOC Sensor

The module with the UART-RS485 converter is designed to work with the Raspberry Pi Pico. It has a built-in SP3485 chip and enables data transmission between the UART interface and the RS485 device. Waveshare Pico-2CH-RS485