150:1 12V 37Dx57L - Metal Gearmotor
search
  • 150:1 12V 37Dx57L - Metal Gearmotor
ID: 580040
zł154.28
Tax included

zł125.43 tax excl.

Motor with 37 mm diameter and 57 mm length, 150:1 metal gear, 12 V operating voltage, 0,2 A to 5,5 A power consumption, 67 RPM speed and 49 maximum torque. Pololu 2829

6 weeks
On request
Kamami is the official distributor of electronic modules and Pololu robotic parts. All products of this brand in our offer are original and come directly from the manufacturer.

 

Free shipping

free shipping in Poland for all orders over 500 PLN

 

Same day shipping

If your payment will be credited to our account by 11:00

 

14 days for return

Each consumer can return the purchased goods within 14 days

Description

This gearmotor consists of a 12 V brushed DC motor combined with a 150:1 metal spur gearbox. The gearmotor is cylindrical, with a diameter just under 37 mm, and the D-shaped output shaft is 6 mm in diameter and 16 mm-long.

Features

  • Supply voltage: 12 V
  • Gear ratio: 150:1
  • Speed: 67 RPM
  • Maximum torque: 49 kg*cm
  • Minimum current consumption: 0,2 A
  • Maximum current consumption: 5,5 A
  • Diameter: 52 mm
  • Length: 73 mm
  • Weight: 210 g

Note!

The listed stall torques and currents are theoretical extrapolations; units will typically stall well before these points as the motors heat up. Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for continuously applied loads is 10 kg-cm (150 oz-in), and the recommended upper limit for instantaneous torque is 25 kg-cm (350 oz-in). Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Supply voltage

Pololu 37D engines are available in two versions with the recommended voltage of 12 V and 24 V. These engines do not differ in power, but only with the current drawn, which for 24 V motors is half as low as for 12 V motors, which can be considerable easier when choosing drivers. It is possible to supply the motor with a lower or higher voltage, but this is associated with lower power or decrease their lifetimes, respectively.

Dimensions and weight

All motors have the same dimensions. Depending on the gear ratio, the gears differ in length, as shown in the technical drawing below. The metal gear housing has two tapped holes for M3 screws. The gearmotors weigh from 175 g to 210 g depending on the gear size.

Dimensions of 37D motors in version with encoders (units in mm).
Dimensions of 37D motors without encoders (units in mm).
Note!
Do not screw too far into the mounting holes as the screws can hit the gears. We recommend screwing no more than 3 mm into the M3 mounting holes.

Magnetic encoder

All Pololu 37D gearmotors are available in versions with a magnetic encoder and without an encoder. The encoder is mounted on an additional shaft on the opposite side of the main shaft. The shaft on which the encoder is mounted is led directly from the motor (without gear), which allows the installation of the encoder which works much more accurately than if it was mounted on the shaft behind the gear. The use of an encoder allows to determine the speed and position of the motor shaft and to apply these values in the PID controller feedback loop.

Single-sided shaft motor Motor with double-sided shaft and mounted encoder A motor with a double-sided shaft, an encoder and a removed plastic cover

Using the encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 8″ (20 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions.

ColorFunction
Red motor power (connects to one motor terminal)
Black motor power (connects to the other motor terminal)
Green encoder GND
Blue encoder Vcc (3.5 V to 20 V)
Yellow encoder A output
White encoder B output
Encoder A and B outputs for 37D mm 12V metal gearmotor with 64 CPR encoder (motor running at 12 V).

Wheels

The 6 mm diameter gearbox output shaft works with Pololu universal aluminum mounting hub for 6mm shafts, which can be used to mount larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft as shown in the left picture below. Alternatively, you could use 6mm scooter wheel adapter to mount many common scooter, skateboard, and inline skate wheels to the gearmotor’s output shaft as shown in the right picture below.

Black Pololu 80x10mm wheels (adapter needed)
White Pololu 80x10mm wheels (adapter needed)
Black Pololu 80x10mm wheel with motor mounted

Wild Thumper wheels Chrome(adapter needed) Wild Thumper wheels red matalic (adapter needed) Wild Thumper wheel with engine mounted

Black scooter/skate wheels with 200 mm, 144 mm, 100 mm, 84 mm, and 70 mm diameters. Aluminum Scooter Wheel Adapters

Brackets

The gearmotor face plate has two mounting holes threaded for M3 screws, and you can use our custom-designed 37D mm metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.

Brackets for 37D engines Brackets for 37D engines 37D engine mounted on a platform with a Scooter wheel

Motor controllers

We have a number of motor controllers and motor drivers that work with these 37D mm metal gearmotors. In particular, we recommend VNH5019-based motor drivers, for which we have basic single and dual carriers and a dual-channel shield for Arduino.

RoboClaw 2x7A Motor Controller (V5B) Pololu Dual VNH5019 Motor Driver Shield for Arduino Jrk G2 24v13 - DC motor controller

Current sensors

We have an assortment of Hall effect-based current sensors to choose from for those who need to monitor motor current:

Current sensor module (0-20A) with ACS712-20 ACHS-7124 Current Sensor Carrier ±40A Pololu 2452 - ACS711EX Current Sensor Carrier -15.5A to +15.5A

Types and parameters of 37D Pololu engines:

Our offer includes motors with gear ratios from 6.3: 1 to 150: 1, with a rated voltage of 12 V and 24 V. All variants of motors with gears are available with and without a magnetic encoder. In addition, gearedless encoder motors are available to fit gears from the rest of the 37D motors.

Gear ratio

Rated
Voltage
No-Load Speed Stall Torque No-Load
Current
Stall
Current
Single-Shaft Dual-Shaft
1:1 24 V 10 000 RPM 0.55 kg*cm 0.1 A 3 A LINK
12 V 10 000 RPM 0.5 kg*cm 0.2 A 5.5 A LINK
6.3:1 24 V 1 600 RPM 3.0 kg*cm 0.1 A 3 A LINK LINK
12 V 1 600 RPM 3.5 kg*cm 0.2 A 5.5 A LINK LINK
10:1 24 V 1 000 RPM 5.5 kg*cm 0.1 A 3 A LINK LINK
12 V 1 000 RPM 4.9 kg*cm 0.2 A 5.5 A LINK LINK
19:1 24 V 530 RPM 9.5 kg*cm 0.1 A 3 A LINK LINK
12 V 530 RPM 8.5 kg*cm 0.2 A 5.5 A LINK LINK
30:1 24 V 330 RPM 15 kg*cm 0.1 A 3 A LINK LINK
12 V 330 RPM 14 kg*cm 0.2 A 5.5 A LINK LINK
50:1 24 V 200 RPM 23 kg*cm 0.1 A 3 A LINK LINK
12 V 200 RPM 21 kg*cm 0.2 A 5.5 A LINK LINK
70:1 24 V 140 RPM 31 kg*cm 0.1 A 3 A LINK LINK
12 V 150 RPM 27 kg*cm 0.2 A 5.5 A LINK LINK
100:1 24 V 100 RPM 39 kg*cm 0.1 A 3 A LINK LINK
12 V 100 RPM 34 kg*cm 0.2 A 5.5 A LINK LINK
131:1 24 V 79 RPM 47 kg*cm 0.1 A 3 A LINK LINK
12 V 76 RPM 45 kg*cm 0.2 A 5.5 A LINK LINK
150:1 24 V 68 RPM 56 kg*cm 0.1 A 3 A LINK LINK
12 V 67 RPM 49 kg*cm 0.2 A 5.5 A LINK LINK
580040

Data sheet

DC motor power
Other
Gear material
Metal
Gear ratio
150:1
Rotation speed
67
Shaft diameter
6 mm
Shaft shape
D
Obustronny wał silnika
Nie
Power supply voltage
12V

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Other products in the same category (16)