 
        
           
        
          Jrk G2 24v13 USB Motor Controller is a single-channel DC motor driver. The voltage supplying the motors is from 6.5 to 40 V (40 V maximum recommended). The control can be carried out via the USB port, TTL serial interface, I2C, RC receiver signal or via analog input. The controller enables easy implementation of a closed loop of engine speed control by connecting an analog or frequency input. It also allows configuration of engine operation parameters via a USB interface and a free application.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
 No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
 No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
Module with two DRV8830 DC motor drivers. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020010
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
 No product available!
A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with connectors for mounting. Pololu 5065
 No product available!
Dual motor controller that allows you to control two DC motors with 2.7-10.8V voltage and 1.2A continuous current per channel. Pololu 2130
 No product available!
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
Pololu Simple High-Power Motor Controller 24v23
 No product available!
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
RC type ESC controller module dedicated to DC brushed motors with a supply voltage from 4.2 V to 8.4 V and a current consumption of up to 3 A
 No product available!
Pololu Simple Motor Controller 18v7
 No product available!
Two-channel motor controller with L298N system with 4.8 ... 46V motor power supply and 2A current capacity per channel. It has a protection in the form of diodes. DFRobot DRI0002
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037
The ESC RC controller module is designed for brush motors with a supply voltage from 3.5 to 6 V and a capacity of 1 A
ESC type controller for a DC motor with a supply voltage of 3.7 V to 5 V. It offers a maximum output current of up to 1.5 A and allows you to control two motors independently
 No product available!
 
                    DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147