Module with controller of DC motors TB6612FNG for Wemos D1 Mini
ID: 1180538
5906623442898
zł45.61
Tax included
zł37.08 tax excl.
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
Description
A module with a two-channel DC motor driver based on the TB6612FNG system, designed for Wemos D1 Mini boards. They allow you to drive two DC motors with a voltage from 4.5 to 15 V and a continuous current of 1 A per channel. It uses the built-in STM32F030 microcontroller, which directly controls the H-bridge system. The module communicates via the I2C interface.
Features
- TB6612FNG chip
- Motor voltage: 4.5 to 15 V
- Logic voltage: 3.3 V
- Maximum output current (instantaneous): 3 A per channel
- Continuous output current: 1 A per channel
- Maximum PWM frequency: 100kHz
- I2C interface
- I2C address: 0x2D to 0x30
Kit contains
- Module with a driver of DC motors for Wemos D1
- 3 x 8-pin male goldpin connector
1180538
Data sheet
- Output current
- 1A
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 15 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Development board with dimensions and spacing compatible with Arduino Uno R3. It have built-in Wi-Fi ESP8266 module. The device is compatible with WeDOS D1, it can be programmed from the level of Arduino IDE
zł25.31
24h
Available quantity: 15
Available
Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini
zł19.36
24h
Available quantity: 18
Available
BMP180 temperature / pressure sensor module compatible with WeMos D1 mini board.
zł5.45
24h
Available quantity: 8
Available
Module with 0.66 "OLED display with 64x48 resolution for D1 Mini PCB with I2C interface. WeMos OLED Shield
zł12.87
24h
Available quantity: 5
Available
Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x
zł18.70
24h
Available quantity: 30
Available
Development board D1 Mini Pro with WiFi ESP8266 module and 16 MB Flash memory, equipped with ceramic antenna and external antenna connector. The module can be programmed from the Arduino IDE level. WeMos D1 Mini Pro
zł25.71
24h
Available quantity: 14
Available
Other products in the same category (16)
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
24h
Available quantity: 1
Available
Single-channel DC motor driver that can control the movement of the drive with a supply voltage of up to 36 V and a current consumption of up to 15 A. Controlled by a PWM signal. DFRobot DRI0042
zł129.97
24h
Available quantity: 3
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5058
zł431.43
4 weeks
No product available!
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
zł467.81
3 weeks
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
zł111.29
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5046
zł435.53
4 weeks
No product available!
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
The board based on the L298 Dual Full-Bridge Motor Driver; can provide up to 4 Amps of current to the motors (2 Amps per motor). ROB-09571
zł167.12
24h
Available quantity: 3
Available
Direct current motor driver (DC) with a working voltage from 5 to 30 V and a maximum continuous current of 30 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD30C
zł138.34
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5057
zł459.97
4 weeks
No product available!
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł56.25
24h
Available quantity: 1
Available
Dual-channel electric motors controller (H-bridge) Arduino Motor Shield Rev3 with L298 for controlling two DC motors or one stepper motor with the possibility of using an electronic brake.
zł143.53
3 weeks
No product available!
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
zł86.42
24h
Available quantity: 2
Available
Two-channel motor controller with L298N system with 4.8 ... 46V motor power supply and 2A current capacity per channel. It has a protection in the form of diodes. DFRobot DRI0002
zł56.05
24h
Available quantity: 2
Available
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
zł34.71
24h
Available quantity: 2
Available
Dual VNH3SP30 Motor Driver Carrier MD03A
zł1,136.89
24h
Available quantity: 2
Available
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini