Pololu G2 18v15 HP - DC Motor Driver (assembled)
ID: 573139
5906623479627
zł500.01
Tax included
zł406.51 tax excl.
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
Description
Pololu G2 18v15 High Power is a DC motor controller in the form of a H bridge, built based on N-MOSFET transistors. The module can be supplied with voltage from the range of 6.5 ... 30 V. The maximum continuous current supplying the DC motor is 15 A. The controller does not require additional cooling. The controller module has a current measurement circuit taken by the motor which allows setting the current limit. The motor is controlled by means of RC signal, through the I2C interface, UART interface, USB interface or analog interface. The logic part of the controller works with a 3.3V voltage. The software update of the controller and the configuration takes place via the USB interface. The module has soldered connectors.
Attention!
The set does not include a USB cable . It should be purchased separately.
properties
- Supply voltage: 6.5 V to 30 V (absolute maximum)
- Continuous output current: 15 A
- Adjustable maximum acceleration and delay
- Adjustable initial and maximum speed
- Possibility of braking or running
- Input calibration for analog and RC signals
- Adjustable threshold and reaction to excessive temperature
- Adjustable PWM frequency from 1.13 kHz to 22.5 kHz
- Error LED connected to the digital ERR output
- Protection against back voltage
- Short-circuit protection
- Current measurement circuit for the motor
- The controller's logic is powered by 3.3V
- Dimensions: 53.5 x 28 x 12.7 mm
- Weight: 12.5 g
573139
Data sheet
- Output current
- 15 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 30 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł184.19
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł216.36
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
Delivery date unknown
No product available!
Other products in the same category (16)
Module with a 2-channel DC motor driver TB6612FNG designed to work with micro: bit. It can also control 3 servos. SB Components 14897
zł76.94
24h
Available quantity: 2
Available
Module with 2-channel DC motor driver DRV8833 designed to work with the Raspberry Pi Pico. It can work with a voltage from 2.7 to 10.8 V and a current of up to 1.2 A. Pimoroni PIM617
zł57.27
24h
Available quantity: 2
Available
DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1
zł95.96
24h
Available quantity: 2
Available
Pololu TReX Dual Motor Controller DMC01
zł1,054.63
24h
Available quantity: 1
Available
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
zł467.81
3 weeks
No product available!
Module with DC motor driver DRV8256E. It can work with motors supplied with the voltage from 4.5 to 48 V and the current consumption up to 1.9 A. Pololu 4038
zł72.59
24h
Available quantity: 2
Available
Two-channel driver of direct current (DC) motors with an operating voltage from 4 to 16 V and a maximum continuous current of 3 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD3A
zł35.01
24h
Available quantity: 9
Available
Dual motor controller that allows you to control two DC motors with 2.7-10.8V voltage and 1.2A continuous current per channel. Pololu 2130
zł43.00
4 weeks
No product available!
Pololu Simple Motor Controller 18v7 (Fully Assembled)
zł783.23
24h
Available quantity: 1
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. Board with soldered connectors. Pololu 5062
zł89.05
4 weeks
No product available!
Pololu High-Power Motor Driver 36v15
zł229.65
24h
Available quantity: 1
Available
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
zł53.53
24h
Available quantity: 5
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
zł56.04
24h
Available quantity: 1
Available
Direct current motor driver (DC) with a working voltage from 7 to 58 V and a maximum continuous current of 25 A. It can be controlled by a PWM signal, a potentiometer or by means of built-in buttons. Cytron MD25HV
zł250.56
24h
Available quantity: 7
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5037
zł327.65
4 weeks
No product available!
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
zł84.92
24h
Available quantity: 2
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362