Pololu G2 24v12 HP - DC motor controller
ID: 573142
zł559.49
Tax included
zł454.87 tax excl.
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1365
Description
Pololu G2 24v12 High Power is a DC motor controller in the form of a H bridge, built based on N-MOSFET transistors. The module can be supplied with voltage from the range of 6.5 ... 30 V. The maximum continuous current supplying the DC motor is 12 A. The controller does not require additional cooling. The controller module has a current measurement circuit taken by the motor which allows setting the current limit. The motor is controlled by means of RC signal, through the I2C interface, UART interface, USB interface or analog interface. The logic part of the controller works with a 3.3V voltage. The software update of the controller and the configuration takes place via the USB interface.
Attention!
The set does not include a USB cable . It should be purchased separately.
properties
- Supply voltage: 6.5 V to 30 V (absolute maximum)
- Continuous output current: 12 A
- Adjustable maximum acceleration and delay
- Adjustable initial and maximum speed
- Possibility of braking or running
- Input calibration for analog and RC signals
- Adjustable threshold and reaction to excessive temperature
- Adjustable PWM frequency from 1.13 kHz to 22.5 kHz
- Error LED connected to the digital ERR output
- Protection against back voltage
- Short-circuit protection
- Current measurement circuit for the motor
- The controller's logic is powered by 3.3V
- Dimensions: 53.5 x 28 x 10.7 mm
- Weight: 7.5 g
Included
- The Pololu G2 24v12 driver module
- 2x screw connection 2 pin
- 2x male goldpin connector
- jumper
573142
Data sheet
- Output current
- 12 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 30 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł184.19
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł500.01
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
24h
Available quantity: 1
Available
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1364
zł592.18
24h
Available quantity: 1
Available
Other products in the same category (16)
DC motor driver that allows you to control the movement of three drives using the I2C interface. The set includes only the board without connectors. Pololu 5032
zł177.08
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
zł354.03
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5047
zł406.69
4 weeks
No product available!
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
zł294.77
4 weeks
No product available!
Pololu Dual MC33926 Motor Driver Shield for Arduino
zł197.80
24h
Available quantity: 2
Available
DC motor driver with voltage 6.5..30V and maximum continuous current 27A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3148
zł629.10
4 weeks
No product available!
An H-bridge driver that provides bidirectional control of a high-power DC motor with a voltage range of 5-60 V and a continuous current of up to 11 A. The module supports PWM signals up to 100 kHz, features a current measurement (CS) output based on the ACS711 sensor, and features reverse polarity and short-circuit protection. It is compatible with both 3.3 V and 5 V logic, enabling easy integration with popular microcontroller platforms. Ideal for robotics, automation, and DIY projects requiring high performance and reliability. Pololu 2993
zł215.13
6 weeks
No product available!
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450
zł81.77
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
zł332.37
4 weeks
No product available!
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
This L298N module allows independent control of two DC motors or one stepper motor, ideal for robotics and DIY projects. It supports power supplies from 7V to 35V and has a built-in 5V regulator that can power additional circuits. Control is performed via the ENA, ENB, and IN1–IN4 pins, allowing for adjustable rotational direction and speed. The module is equipped with protection diodes and filter capacitors for stable and reliable operation.
zł8.91
24h
Available quantity: 7
Available
The core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader. This version does not include any through-hole components or connectors, allowing for customized assembly or standalone use. Pololu 3118
zł197.60
24h
Available quantity: 2
Available
A two-channel DC motor controller with a I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5079
zł73.46
24h
Available quantity: 1
Available
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 15 A per channel
zł106.26
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5053
zł305.06
4 weeks
No product available!
DRV8835 Dual Motor Driver Carrier
zł23.90
24h
Available quantity: 4
Available
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1365