Pololu G2 24v12 HP - DC Motor Driver (assembled)
ID: 573141
5906623479641
zł592.18
Tax included
zł481.45 tax excl.
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1364
Description
Pololu G2 24v12 High Power is a DC motor controller in the form of a H bridge, built based on N-MOSFET transistors. The module can be supplied with voltage from the range of 6.5 ... 30 V. The maximum continuous current supplying the DC motor is 12 A. The controller does not require additional cooling. The controller module has a current measurement circuit taken by the motor which allows setting the current limit. The motor is controlled by means of RC signal, through the I2C interface, UART interface, USB interface or analog interface. The logic part of the controller works with a 3.3V voltage. The software update of the controller and the configuration takes place via the USB interface. The module has soldered connectors.
Attention
The set does not include a USB cable. It should be purchased separately.
The set does not include a USB cable. It should be purchased separately.
Features
- Supply voltage: 6.5 V to 30 V (absolute maximum)
- Continuous output current: 12 A
- Adjustable maximum acceleration and delay
- Adjustable initial and maximum speed
- Possibility of braking or running
- Input calibration for analog and RC signals
- Adjustable threshold and reaction to excessive temperature
- Adjustable PWM frequency from 1.13 kHz to 22.5 kHz
- Error LED connected to the digital ERR output
- Protection against back voltage
- Short-circuit protection
- Current measurement circuit for the motor
- The controller's logic is powered by 3.3V
- Dimensions: 53.5 x 28 x 12.7 mm
- Weight: 12.5 g
573141
Data sheet
- Output current
- 12 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 30 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł532.48
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
24h
Available quantity: 1
Available
Other products in the same category (16)
No product available!
The board based on the L298 Dual Full-Bridge Motor Driver; can provide up to 4 Amps of current to the motors (2 Amps per motor). ROB-09571
zł167.12
24h
Available quantity: 3
Available
No product available!
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
zł9.45
24h
Available quantity: 6
Available
Dual H-Bridge motor driver board, 2A, 36V max, L298N, RoHS
zł12.60
24h
Available quantity: 3
Available
(DRI0009) 2A Motor Shield For Arduino
zł61.27
24h
Available quantity: 2
Available
DRV8801 Single Brushed DC Motor Driver Carrier
zł60.64
24h
Available quantity: 2
Available
A4990 Dual Motor Driver Carrier
zł44.97
24h
Available quantity: 1
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
zł294.77
4 weeks
No product available!
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
zł56.70
24h
Available quantity: 2
Available
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Available
Tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. Operating voltage range from 0 V to 11 V, built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature. Pololu 2990
zł17.32
24h
Available quantity: 8
Available
This compact breakout board is for ROHM’s BD65496MUV motor driver, which offers an operating voltage range of 2 V to 16 V and can deliver a continuous 1.2 A to a single brushed DC motor. Pololu 2960
zł71.08
24h
Available quantity: 2
Available
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł113.25
24h
Available quantity: 3
Available
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1364