Pololu Stepper motor controller with MP6500 chip
ID: 569593
5906623478545
zł36.20
Tax included
zł29.43 tax excl.
The stepper motor driver with the MP6500 system allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35 V. Pololu 2966
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
This driver can be used to build a 3D printer or CNC milling machine based on stepper motors. The system used in the controller (MP6500) enables work in the following modes: full step, 1/2 step, 1/4 step and 1/8 step. The mode selection is made by changing the MS1 and MS2 pin states. The controller operates in the 4.5..35 V voltage range and 1.5 A current per phase. The module enables the control of the current limit via a built-in potentiometer (the possibility of increasing the current limit to 2.5 A). It has a number of protections that protect the system from damage. It also has outputs in accordance with the modules based on the A4988 layout, which is why it can act as a substitute. It can work in systems with 3.3 V and 5 V logic.
The module has no soldered goldpin connectors, it is necessary to solder it yourself (goldpin connector is included with the controller).
properties
- Based on the MP6500 chip
- Modes: full step, 1/2 step, 1/4 step and 1/8 step
- Control of the current limit via a built-in potentiometer (possible increase of current to 2.5 A)
- Operating voltage 4.5.35 V
- Maximum current (per phase): 1.5 A
- Protection against overheating, too low voltage, too high current
- It has outputs in accordance with the modules with the A4988 system
- Dimensions: 15 x 20 mm
- Weight: 1.4 g (without soldered connectors)
Included
- Stepper motor controller with MP6500 system
- Goldpin strip for men
569593
Data sheet
- Output current
- 1,5 A
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 35 V
You might also like
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. Polol 2133
zł67.33
24h
Available quantity: 2
Available
DRV8825 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2982
zł84.27
24h
Available quantity: 1
Available
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981
zł80.12
24h
Available quantity: 4
Available
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2980
zł27.13
Delivery date unknown
No product available!
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. It is compatible with Polol 2133
zł7.90
24h
Available quantity: 14
Available
Simple to use stepper motor driver, compatible with anything that can output a digital 0..5V pulse or 0..3.3V pulse. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. ROB-12779
zł87.16
24h
Available quantity: 2
Available
Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. Pololu 2128
zł89.93
24h
Available quantity: 2
Available
This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step modes (from full-step through 1/128-step), back-EMF feedback that can be used for stall detection or optional closed-loop control, and over-current and over-temperature protection.
zł86.70
24h
Available quantity: 3
Available
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/16-step).
Delivery date unknown
No product available!
No product available!
Other products in the same category (16)
Pololu Simple High-Power Motor Controller 24v12 (Fully Assembled)
zł646.75
24h
Available quantity: 2
Available
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
zł933.32
24h
Available quantity: 1
Available
Brushless motor driver module (ESC regulator) with current efficiency up to 20 A. Uses BLHeli_S software
zł41.46
24h
Available quantity: 6
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5040
zł295.54
6 weeks
No product available!
STSPIN220 stepper motor driver module with a low voltage range of 1.8...10V and 1.1A working current. The controller allows you to control the motor motion up to 9 different resolutions (up to 1/256 steps). Pololu 2877
zł45.85
24h
Available quantity: 1
Available
Available
DRV8711 stepper motor driver module powered by 8-50V voltage and 4A operating current. The controller allows you to control the movement of the engine with up to 9 different resolutions. Configuration via SPI interface. Pololu 3730
zł125.29
24h
Available quantity: 7
Available
Dual MC33926 Motor Driver CarrierTwo-channel DC motor controller with voltage from 5 V to 28 V, power consumption up to 3 A per channel. Controlled by PWM signal. Pololu 1213
zł333.75
6 weeks
No product available!
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450
zł73.10
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5057
zł696.22
6 weeks
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł318.53
24h
Available quantity: 1
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł173.75
6 weeks
No product available!
Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be supplied with current up to 1.2 A per phase and with a voltage from 4.5 V to 45 V. Communication via the SPI interface. Pololu 3766
zł54.86
6 weeks
No product available!
Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1
zł56.70
24h
Available quantity: 5
Available
Module with the TMC2209 bipolar stepper motor driver. It enables control with a supply voltage ranging from 4.75 to 29 V and a current of up to 2.8 A
zł20.60
24h
Available quantity: 39
Available
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037
zł24.86
24h
Available quantity: 4
Available
The stepper motor driver with the MP6500 system allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35 V. Pololu 2966