Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500
ID: 561475
zł206.07
Tax included
zł167.54 tax excl.
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3061
Description
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. The module has an uFL connector for connecting an external antenna. Compatible with the 802.11b / g / n standard, it uses the SPI interface for communication. It has support for WEP, WPA, WPA2 security.
Attention!
The ATWINC1500 module located on the board does not have a built-in antenna, for the module to work properly it is necessary to buy an external antenna and connect it to the uFL connector. Also available with a version with a module that has a built-in antenna - Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500.
Built-in lithium-polymer battery connector and charger module enable connection of a 500 mAh Li-Pol battery . The battery is charged via the mounted USB connector.
properties
- Microcontroller: 32-bit ATSAMD21G18 ARM Cortex M0:
- Frequency: 48 MHz
- 256 kB of Flash memory
- 32 kB of RAM
- Built-in Atmel ATWINC1500 WiFi module from Atmel:
- Compliance with the 802.11b / g / n standard
- Interface: SPI
- Support for WEP, WPA, WPA2
- UFL connector for connecting an external antenna
- Power supply via USB (5 V) or Li-Pol (3.7 V) battery (no battery included)
- Built-in Li-Pol battery charger with 200 mA capacity with diode informing about the status
- 20 GPIO pins
- 8 PWM pins
- 10 analog inputs
- 1 analogue output
- Hardware interface support: SPI, I2C, UART
- 4 mounting holes
- Reset button
- Dimensions: 53.6 x 23 x 8 mm without solder connections)
- Weight: 6.1 g
Included
- Adafruit Feather M0 WiFi with uFL module - ATSAMD21 + ATWINC1500
- Men's pin connectors
561475
Data sheet
- Microcontroller
- ATSAMD21G18
- Flash memory
- 256kB
- Number of I/O
- 20
- Ethernet
- none
- WiFi/BT module
- Yes
- Bluetooth module
- No
- MicroSD slot
- No
- Length
- 53,6 mm
- Width
- 23 mm
- USB connector type
- microUSB type B
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Adafruit Feather HUZZAH ESP8266 is a new development board from Adafruit with a built-in WiFi module ESP8266. Processor frequency: 80 MHz, USB-serial TTL CP2104 converter, Li-Pol battery charger. Adafruit 2821
zł90.18
24h
Available quantity: 1
Available
Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3010
zł261.29
24h
Available quantity: 1
Available
Other products in the same category (16)
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619
zł157.76
24h
Available quantity: 1
Available
Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458
zł73.70
24h
Available quantity: 2
Available
The board is equipped with the ATSAMD51J19 microcontroller with ARM Cortex-M4 core and SPI Flash memory, GPIO pins, connector for connecting the battery with the charging circuit. Adafruit 3857
zł119.31
4 weeks
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884
zł79.03
24h
Available quantity: 3
Available
The board is equipped with a STM32F405 microcontroller with an ARM Cortex-M4 core and SPI Flash memory, GPIO pins, a connector for connecting a battery with a charging circuit and a STEMMA QT socket. Adafruit 4382
zł217.59
24h
Available quantity: 1
Available
The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759
zł143.34
4 weeks
No product available!
Development kit with nRF52840 microcontroller with ARM Cortex M4F core and BLE communication. Equipped with motion sensors, magnetometer, light, humidity, pressure sensors and a microphone. Adafruit 4516
zł245.41
4 weeks
No product available!
Module with WiFi Espressif ESP32-S2. It integrates the TFT LCD display, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5300
zł144.23
24h
Available quantity: 2
Available
Module with WiFi Espressif ESP32-S2. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5000
zł87.88
4 weeks
No product available!
Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323
zł92.79
24h
Available quantity: 1
Available
Module with WiFi Espressif ESP32. It offers 8MB Flash, 2MB PSRAM, LiPo charging circuit and RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5438
zł99.68
24h
Available quantity: 2
Available
Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477
zł90.76
4 weeks
No product available!
Module with WiFi and BLE Espressif ESP32-S3 system and LCD TFT display. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5483
zł155.03
24h
Available quantity: 4
Available
A board with an RP2040 microcontroller and a radio module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and a STEMMA QT connector. Adafruit 5712
zł121.44
24h
Available quantity: 3
Available
A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714
zł175.46
24h
Available quantity: 1
Available
Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710
zł85.77
24h
Available quantity: 4
Available
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3061