Segger J-Link ARM-14 Adapter (8.08.01)

Adapter that enables JTAG connection between devices such as J-Link, J-Trace or Flasher and Jacinto7 systems from TI, offering access to JTAG/SWD and Trace connectors with TPIU tracking function. Thanks to high quality of workmanship and versatility, the adapter provides a stable connection, supporting debugging, testing and diagnostic processes in embedded systems. Segger MIPI-60 Adapter (8.06.42)

Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.

J-Link TI-CTI-20 Adapter, RoHS, Segger

A set of three adapters for SO-8, SO-8W and SO-16 memories that allows easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter Board Pack for SO-8, SO-8W, SO-16 (6.40.01)

An adapter that allows you to connect a 20-pin 0.1" connector to a 10-pin connector, allowing you to easily connect J-Link or Flasher programmers to your PCB using through-wires. It is ideal for prototyping, testing new designs and working with ST Discovery boards, offering flexibility, speed and time savings when making design changes.Segger Flying Wire Adapter (06.08.27)

Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)

Advanced evaluation board designed for rapid implementation of embedded solutions. Supporting the embOS operating system and SEGGER tools such as emFile, emWin, emUSB and emNet, the board is an ideal platform for software testing and application development in an environment based on the Xilinx Zynq XC7Z007S SoC with ARM Cortex-A9 processor and Artix7 FPGA. Segger emPower Zynq (6.31.00)

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

A compact reference platform that enables rapid testing and verification of trace configurations, providing excellent signal quality for analysis. With the NXP iMX RT1051/52 microcontroller and support for the SWD debug interface, the board provides high performance and flexibility in monitoring system performance. Segger NXP iMX RT1050 Trace Reference Board (6.68.19)

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)

Adapter from the standard 20-pin 2.54 mm connector to the 10-pin 1.27 mm connector often used in Cortex-M boards. Segger 50-Mil 10-Pin Patch Adapter (8.06.28)

J-Link 6-pin Needle Adapter (8.06.16)

J-Link RX Adapter, RoHS, Segger

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)