zł13.86 tax excl.
Module with temperature and humidity sensor DHT11. It uses a 1-wire communication interface and has a humidity measurement range from 20 to 90% with an accuracy of 5% and temperature from 0 to 50 ºC with an accuracy of 2 ºC
Module with DHT11 temperature and humidity sensor with 1-wire communication interface. The sensor measures humidity in the range from 20 to 90% with an accuracy of 5%, and temperature in the range from 0 to 50 ºC with an accuracy of 2 ºC. The sensor is equipped with an 8-bit microcontroller that converts the signal from the sensor correcting it with the parameters set during the factory calibration to the digital signal of the 1-wire bus, allowing for easy reading of the measurement results. The module uses the XH2.54 connector. It will be used in simple weather stations.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Temperature and Humidity Sensor, RoHS
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Digital-output relative humidity and temperature sensor, RoHS
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Module with temperature and humidity sensor DHT11. It allows you to measure humidity in the range of 20 ... 90% and temperature (0 ... 50 ° C). DFRobot DFR0067
Digital temperature and humidity sensor with calibrated digital output signal. Equipped with a 2.5 mm 4-pin male stereo audio connector that works perfectly with the Sonoff TH10/TH16 socket. Sonoff Si7021
Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588
Module with temperature, humidity and pressure sensor BME680 from Bosch. The module communicates via I2C or SPI interfaces.
No product available!
Air humidity and temperature sensor with 1-Wire interface.
Grove module with temperature, humidity and pressure sensor. The board is equipped with a Grove connector and communicates via I2C or SPI. Seeed Studio 101020193
No product available!
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. Equipped with a Gravity DFRobot SEN0334 connector
No product available!
Module with a digital temperature and humidity sensor based on the SHT35. Communication via the I2C interface. DFRobot SEN0333
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. DFRobot SEN0332
Module with a digital temperature and humidity sensor based on the SHT31. Communication via the I2C interface. DFRobot SEN0331
Module with a digital temperature and humidity sensor based on the SHT30. Communication via the I2C interface. DFRobot SEN0330
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. SparkFun SEN-16467
Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C (Qwiic). SparkFun SEN-15440
Module with a temperature and humidity sensor DHT22. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0137
Module with temperature and humidity sensor DHT11. It uses a 1-wire communication interface and has a humidity measurement range from 20 to 90% with an accuracy of 5% and temperature from 0 to 50 ºC with an accuracy of 2 ºC