Best sellers
There are 16477 products.
Universal oscilloscope probe with BNC plug with 100: 1 voltage divider and 100 MHz bandwidth. It allows you to perform measurements with a maximum voltage of 2 kV
Module with LED driver. It can control LED strips with a length of 1 to 2 meters at a voltage of 9 V or from 1 to 5 meters at a voltage of 12 V. Seeed Studio 105020002
Ethernet network module with W5500 chip. It communicates via the SPI interface, it has a built-in TCP/IP stack. There are two Grove connectors with I2C and UART on the board. Seeed Studio 103030021
Active HDTV antenna with 28 dB amplification, supporting FullHD and 4K UltraHD standard. Designed for indoor installation. BLOW ATD40
Module with a vertical USB Type-C connector intended for device prototyping. The pins are placed on a connector with a 2.54 mm pitch, which greatly facilitates the use of USB Type C, e.g. with breadboards. SparkFun BOB-23055
OLED display 128x64 pixels, white characters / black background, 1.3-3V power supply, SSD1306 or SH1106G controller, communication via I2C and SPI interfaces, PARALLEL WHITE display color, working temperature from -40 to +70, ext. CAP
An extensive development board designed specifically for robotics projects. The set uses the ESP32-S3 microcontroller, which is equipped with a camera enabling video transmission and remote control via WiFi and Bluetooth. DFRobot DFR0994
An extensive CAN to Ethernet converter adapted to difficult industrial conditions. It supports two CAN interfaces, one Ethernet interface and a TCP/IP protocol stack. It also has one RS485 serial port. USR-CANET200
Set of 10 diamond coated needle files, working length 50 mm. Yato YT-6144
Module with OV5647 sensor cooperating with ODROID-M1. It uses a built-in movable IR-CUT filter that is turned on and off automatically depending on the lighting conditions. Odroid M1 MIPI-CSI Camera Kit
8" TFT LCD display with a touch panel dedicated to Odroid-M1 minicomputers. Equipped with MIPI-DSI interface. It has a resolution of 1280x800 pixels. ODROID-Vu8M
The Sipeed RV Debugger Plus is a compact RISC-V BL702 programmer/debugger featuring JTAG and USB-TTL interfaces, ideal for debugging bare metal, UBOOT, and Linux environments
4-in-1 module designed for 18650 Li-Ion batteries. It can be used as a 5 V voltage source, charger, UPS and battery protection module
Set of 10 diamond-coated needle files with a working length of 25 mm. Yato YT-6145
Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18425
Set of 10 diamond coated needle files, working length 50 mm. Yato YT-6151
Set of 5 diamond coated needle files with a working length of 70 mm. Yato YT-6156
Extension module with Li-Ion and LiPo charger dedicated to QT Py boards. It allows you to charge the batteries with a current of up to 200 mA. Adafruit 5397
The PCIe Expansion HAT+ for Gigabit ETH USB3.2 allows the Raspberry Pi 5 to be extended with three high-speed USB 3.2 Gen1 ports and one Gigabit Ethernet connector, using the 16-pin PCIe interface. The device operates without the need for driver installation and offers full support for popular Linux systems. Thanks to additional features such as power monitoring and USB port power control, the module is ideal for advanced networking projects, home servers, and expanded workstations based on the Raspberry Pi 5.
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389