Best sellers
There are 16502 products.
A compact panel thermometer with a clear and easy-to-read LCD display and a measurement probe. Designed for both indoor and outdoor use, it allows checking the current temperature and time (in 12/24-hour format). The temperature measurement result can be displayed in either Celsius or Fahrenheit.
The 4120 automotive relay socket is a 5-pin connector with 18 cm long wires and a built-in rectifier diode that protects the control system from overvoltages, increasing the reliability of the vehicle\'s electrical system
A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules
STM32L4S9VIT6, Ultra-low-power with FPU ARM Cortex-M4 MCU 120 MHz with 2048 kbytes Flash, USB OTG, DFSDM, LCD-TFT, MIPI DSI, AES-256, HASH, LQFP-100
Camera module with Sony Starvis IMX290 sensor that works with Raspberry Pi minicomputers. It has a 2 MP sensor and an 80° viewing angle lens, and is equipped with a movable IR-CUT filter. ArduCAM B0424
Li-Po battery 3.7V / 220mAh. Connector + JST-BEC 2,54, 2 pins, PCM protection, cable length 150mm. Akyga LP402036
BMA400 3-axis accelerometer module with a measurement range of up to ±16g. The board is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-21207
ART.AGT-325 Carbon thermal paste with a thermal conductivity of 15.2 W/mK effectively transfers heat from processors, graphics cards, and other components. Its stable and durable formula with carbon nanoparticles ensures high cooling performance and safe use in demanding systems.
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648
A switching converter that stabilizes a 5V input voltage from 2.6V to 20V. It offers high efficiency of 70-95% and the ability to operate with a continuous input current of up to 900mA and a peak current limit of 2.2A. With a switching frequency of 1.6MHz and a power-saving mode, it is suitable for both high-performance and low-power applications. Pololu 5581
Alphanumeric LCD 16x2 character display module with backlight and RGB text. Equipped with I2C converter and 6 buttons. DFRobot DFR0936
A switching converter that regulates 24V voltage from an input range of 2.6V to 20V. It offers high efficiency of 70-95% and the ability to operate with a continuous input current of up to 900mA and a peak current limit of 2.2A. With a switching frequency of 1.6MHz and a power-saving mode, it is suitable for both high-performance and low-power applications. Pololu 5588
An 8" IPS LCD display with touch panel. It is equipped with HDMI for video display and USB Type-C for touchscreen. It has a resolution of 1280x800 pixels. Waveshare 8DP-CAPLCD
HS01 is a precision soldering iron for PCB electronics soldering. Depending on the value of the supply voltage, it can reach the power of 65W or even 95W. The HS01 soldering iron has a digital OLED display and its operation is controlled by an ARM 32-bit processor. Thanks to the USB-C connector, we can use USB PD chargers for power. The tip is integrated with the heater and reaches the set temperature very quickly within a few seconds
Finder 26.01.8.230.0000 is an impulse relay with a single NO contact, designed for installation in mounting boxes. It enables the control of circuits with a maximum current of 10 A at a voltage of up to 250 V AC. The relay coil is powered by 230 V AC, making it suitable for use in standard electrical installations.
ARM Cortex-M3 CPU, Low power, 256kB Flash, 32kB RAM, USB, 3xUART, 2xI2C, 2xSPI, ADC, DAC, STM, LQFP64, RoHS
Hermetic enclosure ZP90.90.60 made of white ASA with a poured gasket and brass bushings, without mounting lugs. Designed for mounting electronic components in applications requiring IP67 tightness.
LED RGB WS2812B, Black Strip, 5m, 30LEDs / m, no waterproof
Multifunction USB tester. It allows you to check the voltage and current flowing through the USB socket and to control the capacity, energy, power, temperature, time and impedance. MX18USB
The product is intended for testing carbon monoxide detectors and tobacco smoke detectors. Allows you to easily and quickly check the correct operation of the CO sensor. It does not corrode plastic elements, does not leave stains and does not contaminate detectors. AG Termopasty ART.AGT-212