Best sellers
There are 17373 products.
Precise solar radiation intensity sensor in the range from 400 to 1100 nm, communicating via Modbus-RTU (RS485) and resistant to harsh conditions thanks to the aluminum housing class IP67. High accuracy (±5%), fast response time (≤10 s) and resistance to dirt make it ideal for monitoring photovoltaics, environmental research and meteorology. DFRobot SEN0640
Gravity: Digital Peristaltic Pump is a peristaltic pump with a controller and a connector compatible with modeling servos. The set is powered by 5 ... 6 V. DFRobot DFR0523
Driver enabling operation of displays with an RGB-666 connector with resolutions from 480x272 to 800x600 pixels. Equipped with an ESP32-S3 microcontroller with 16 MB Flash memory and 8 MB PSRAM memory. Powered and programmable via USB Type-C connector. Adafruit 5800
A module with a high precision temperature sensor based on the STS35 system. It allows measurement with an accuracy of ±0.1° C and communicates via the I2C interface. DFRobot SEN0434
Step-Up/Step-Down converter module based on the S13V10F5 system. It has an input voltage from 2.8 to 22 V and an output voltage of 5 V. The current efficiency of the converter is up to 1 A. Pololu 4083
A-Star 328P Micro is a small board based on ATmega 328PB microcontroller (Flash, 32 KB, SRAM, 2.5 KB, EEPROM, 1KB, 16 MHz). The system has a loaded bootloader compatible with Arduino. The board has 24 I / O ports (of which 9 pins can be used for PWM outputs and 8 pins for analog inputs). Supply voltage 5.5 ... 15 V. The board works with 5 volts logic voltage. Pololu 3160
Module with proximity and ambient light sensor based on the VCNL4020 system. It allows you to detect obstacles in the range from 0 to 20 cm and measure light intensity from 0.26 to 16,000 lux. It communicates via the I2C bus. Adafruit 5810
A-Star 328P Micro is a small board based on ATmega 328PB microcontroller. The system has a loaded bootloader compatible with Arduino. The board has 24 I / O ports . The circuit board works with 5 volts logic voltage. Polol 3161
Module with digital barometer ICP-10111. The system enables pressure measurement in the range from 300 to 1100 hPa with an accuracy of 1 Pa. DFRobot SEN0517
Module with digital barometer ICP-10111. The system enables pressure measurement in the range from 300 to 1100 hPa with an accuracy of 1 Pa. DFRobot SEN0516
A-Star 328P Micro is a small board based on ATmega 328PB microcontroller (Flash, 32 KB, SRAM, 2.5 KB, EEPROM, 1KB, 8 MHz). The system has a loaded bootloader compatible with Arduino. The board has 24 I / O ports (of which 9 pins can be used for PWM outputs and 8 pins for analog inputs). Supply voltage 3.8-15 V. The board works with 3.3 V voltage. Pololu 3162
A-Star 328P Micro is a small board based on ATmega 328PB microcontroller (Flash, 32 KB, SRAM, 2.5 KB, EEPROM, 1KB, 12 MHz). The system has a loaded bootloader compatible with Arduino. The board has 24 I / O ports (of which 9 pins can be used for PWM outputs and 8 pins for analog inputs). Supply voltage 3.8 ... 15 V. The board works with 3.3 V voltage. Pololu 3163
A pin expander designed for Raspberry Pi Pico boards. It is equipped with a standard female connector and two sets (male and female) of 2x20 pins. DFRobot DFR0836
UART-RS485 converter module based on the TD (H) 541S485H chip. Equipped with power isolation and TVS. DFRobot DFR0845
NEO TOOLS 71-030 is a compact 20 cm aluminum spirit level with two vials, providing precise horizontal and vertical measurements. Its solid construction and accuracy below 0.5 mm/m make it a suitable tool for both professional and household use.
Zestaw nieekranowanych wtyków sieciowych RJ-45 kat.6. Wyposażone są w potrójne zęby, co umożliwia ich zastosowanie zarówno w przypadku kabli drucianych, jak i linkowych. Lanberg PLU-6000EZ
The Discovery kit enables a wide diversity of applications by exploiting low-power communication, multiway sensing and Arm® Cortex® -M4 core-based STM32L4 Series features
Tip GD-3 No. 054 mounted on the heater. Suitable for all types of Elwik soldering irons.
Tip GD-3 No. 056 mounted on the heater. Suitable for all types of Elwik soldering irons.