Best sellers

Adafruit VL53L0X Time of Flight Distance Sensor is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is powered by 2.8 ... 5V voltage and can measure up to 1000mm. Adafruit 3317

IoT module with ATmega328P and BLE4.1 microcontroller. Compatible with the Bluno series, it can be programmed in the Arduino IDE. DFRobot DFR0492

The X-NUCLEO-LPM01A is a 1.8 V to 3.3 V programmable power supply source with advanced power consumption measurement capability

ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316

This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This low-brightness version draws an average of 8 mA at 5 V and has a typical sensing range up to approximately 12 inches (30 cm).

Switching power supply from MEAN WELL with 50W, 5V DC output voltage and 10A output current. Mounting on a DIN rail. Built-in overload and short-circuit protection. MDR-60-5

PROLINE glue gun with a diameter of 11 mm and power of 200 W

The UM7 orientation sensor from Redshift Labs is an Attitude and Heading Reference System (AHRS) that contains a three-axis accelerometer, rate gyro, and magnetometer. It combines this data using an Extended Kalman Filter to produce attitude and heading estimates.

Single board computer with ARM Cortex-A8 AM335x processor, clocked at 1 GHz with 512 MB of RAM. The module has, among others USB interfaces, I / O pins, WiFi and Bluetooth. SeeedStudio 102010048

Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221

Orange filament ABS 1.75 mm 750g

Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000

Self-assembly case designed for minicomputers Odroid H3 and Odroid H3+. Equipped with a place for a fan. Hardkernel ODROID-H3 Case Type 2

Self-assembly case designed for minicomputers Odroid H3 and Odroid H3+. Equipped with a slot for a network card and two slots for a 2.5" SATA drive. Hardkernel ODROID-H3 Case Type 7

7-segment LED display, 1 digit 38.10mm, bright green (575nm), 15,000ucd (10mA), common anode, Pb-free. LED1-AS-B-15011BMG

Camera module with Sony IMX219 sensor works with all versions of Raspberry Pi. The camera is equipped with a matrix with a resolution of 8 MPx, the maximum video resolution is 1080p. ArduCAM B0102

Board with prototype holes dedicated to Raspberry Pi Pico. It offers an 8x20 hole area with a pitch of 2.54 mm with marked pin labels and a reset button and STEMMA QT connector. Adafruit 5200

1.5 hPa resolution pressure sensor from Freescale. The sensor is soldered onto a PCB with 10K pull-up resistors on the I2C pins. Adafruit 992

Arducam USB shield is a module that allows you to connect some ArduCam cameras to a PC or minicomputers, eg Raspberry Pi, BeagleBone etc. The module supports most cameras with a serial interface that have a resolution of 0.3 ... 14 MPix. Attached to the module are appropriate libraries that facilitate image processing, eg using OpenCV software. ArduCam B0095

Step-Down DC-DC converter module based on the D24V150F12 chip. Input voltage 14.5 ... 40V, output voltage 12V (max 15A). Pololu 2885