Best sellers

Digital oscilloscope equipped with a 7" TFT LCD display. It has four measurement channels with a 50 MHz bandwidth, a sampling rate of 1 GSa/s and a 24 Mpts memory buffer. Rigol DS1054Z

Recognizes the distance of an object away from the sensor up to about 10 inches (~25cm) and the location of the object from side to side across the sensor in about a 6 inch (~15cm) span. You will be able to use I2C or UART to communicate with the ZX Sensor via an Arduino-based microcontroller as well as a computer. SEN-12780

The 24 V relay module with adjustable delay time offers a practical solution for AC/DC load control in automation and electronics applications

Light-sensing Infrared LED Board

A four-port USB 2.0 hub that allows data transfer at speeds up to 12Mbit / s. It has a black housing and a 45cm long cable

The ring has sixteen RGB WS2812 diodes, controlled by means of serial signals. The module can be supplied with voltage from 4-7V, only one signal line is required to control it. NeoPixel Ring 16 x WS2812

ATTINY44A-PU

ATtiny44A-PU is a microcontroller from the AVR family in the DIP14 housing, it is equipped with memory: 2 kB Flash, 128 B SRAM, 128 B EEPROM. The power supply voltage is 4.5..5.5 V, the maximum clock speed is 20 MHz.

The third hand ZD-10H is a mounting bracket with a magnifying glass 2.5 times on a cast iron stand

Industrial input/output expansion board based on VNI8200XP and CLT01-38SQ7 for STM32 Nucleo

STM32 Nucleo-32 development board with STM32F042K6T6 MCU, supports Arduino connectivity

A small USB 2.0 hub that allows you to disable individual devices connected to its USB ports, as well as a visual evaluation of the number of devices enabled. It has a built-in connector for the external power supply, so it can act as an active hub. Cable with a length of 40cm, 4 USB ports

USB splitter allowing to connect up to 4 USB devices. It has a cable with a length of 80cm, a power indicator and the possibility of powering from an external source with a microUSB connector

The Akyga AKY1140 CR2032 HP2D lithium battery with a voltage of 3V and a capacity of 210 mAh features 2-pin terminals with a 20 mm pitch, facilitating easy installation in electronic circuits. Utilizing Li-MnO₂ technology, it ensures stable voltage and long lifespan, making it ideal for applications such as real-time clocks, controllers, and memory modules.

Red laser diode module with 5mW power, displaying the point. Ideally suited as a laser pointer, and thanks to the built-in controller, it is possible to power 3 ... 5V. LD-G650A03 - Point

The cable allows you to attach a USB device (eg keyboard, mouse, Flash memory) to the device with microUSB OTG connector. The cord has a length of 14cm

This module can be applied to motor speed measurement, objective position detection, smart car, electronic building blocks, etc.

Waveshare 8 Push Buttons module provides 8 single push buttons in 1 board. Waveshare 3678

INEMO system: 3D accelerometer and 3D gyroscope in LGA16L housing, made by STMicroelectronics. Allows measurement of acceleration up to 16g and angular velocity up to 2000 degrees / second, communication takes place on the I2C / SPI bus

The Microchip system in the DIP8 housing, a dual driver, allows the MOSFET transistors to be controlled with a high switching speed. The controller is characterized by low power consumption, high current efficiency when loading eg gate capacity, or ESD resistance up to 4kV

Female 10-pin straight connector for 2-pin gold-plated plugs. Connector for THT THT