Bluetooth module with built-in CC2541 chip. The module is small, energy-saving and easy to use. It has pads for surface soldering (SMD).
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The module with the HC-05 transceiver makes it easy to add Bluetooth communication to an existing project. The system is controlled by exchanging AT commands (UART bus). FC-114
HC-08 is a module operating in the Bluetooth Low Energy 4.0 standard. The system has a built-in antenna and small dimensions, and thanks to edge joints it can be surface soldered. The module is configured via AT commands
Bluetooth module with integrated HC-08 system. Thanks to the angular pin connector with the bus signals, it is possible to easily connect the module to the contact plate or wires
No product available!
DFRobot BLE4.1 Module is a Bluetooth 4.1 module with DA14681 processor with 3.3 V power supply. It is characterized by low energy consumption and advanced energy management system (built-in charging module). DFRobot TEL0120
Bluetooth 4.0 BLE module powered with 3.3V voltage based on SOC TI CC2541 (On Chip). The module has a range of up to 10m and communicates via the UART interface.
Bluetooth module v2.0 + EDR, controlled by AT + commands with built-in antenna.
Bluetooth 4.0 dongle as a USB adapter. Works with bluetooth devices such as speakers, headsets, smartphones, tablets, keyboards, mice, printers, projectors etc.
The module with the HC-05 transceiver makes it easy to add Bluetooth communication to an existing project. The system is controlled by exchanging AT commands (UART bus). FC-114
A development board that combines the u-blox NINA-B306 Bluetooth module, the ISM330DHCX 6DoF IMU sensor, and the BME280 atmospheric pressure sensor. It has a built-in Qwiic connector and LiPo battery connector as well as a charger and LiPo parameters monitor. SparkFun WRL-20854
No product available!
WiFi/BLE module that supports both the 2.4 GHz and 5 GHz WiFi bands, as well as Bluetooth Low Energy (BLE 4.2) communication. It has a built-in chip antenna and 2.54 mm pitch connectors, which greatly facilitate prototyping. Tibbo WA2000C
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
Crowtail – Bluetooth-compatible Low Energy Module is a small BLE + EDR communication module intended for wireless data transmission in IoT and automation projects. It enables fast serial-interface connection with mobile devices or computers.
Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2
No product available!
Board with the Artemis chip, the GNSS ZOE-M8Q module and the Iridium 9603N satellite receiver. It allows you to send and receive short messages with data anywhere in the world. SparkFun WRL-18712
No product available!
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
Bluetooth module v2.0 + EDR (master / slave), controlled by AT + commands with built-in antenna.
Evaluation Kit with Bluetooth 5.0 BT401. It is equipped with a microSD slot, microUSB connector and two audio outputs. DFRobot DFR0782
Bluetooth module with built-in CC2541 chip. The module is small, energy-saving and easy to use