New products
New products
zł59.04
Delivery date unknown
zł62.71
24h
Available
ACS724 Current Sensor Carrier - ACS724 ±10A current sensor module
ID: 1186900
zł52.90
Tax included
zł43.01 tax excl.
ACS724LLCTR-10AB current sensor module with a DC and AC measurement range from -10 to +10 A. It communicates via an analog interface. Pololu 4043
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with a two-way Hall current sensor based on the ACS724LLCTR-10AB chip. It allows you to measure the current in the range from -10 to 10 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (200 mV/A) centered at 2.5 V with an error of ± 1%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -10 to 10 A
- Output resolution 0.2 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
1186900
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±10 A
- Sposób podłączenia
- Szeregowy
You might also like
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.90
24h
Available quantity: 1247
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.34
Delivery date unknown
No product available!
Other products in the same category (16)
Power monitor module that detects voltages up to 60 VDC and current up to 30 A. It uses the Allegro MicroSystems ACS37800 IC, which simplifies adding monitoring to power systems. SparkFun SPX-17873
zł179.00
6 weeks
No product available!
Bidirectional current sensor module based on the ACS724 circuit. It allows you to measure current in the range -50A to + 50A. It operates with a voltage of 4.5V to 5.5V and is intended for use in 5V systems. Pololu 4049
zł58.22
24h
Available quantity: 1
Available
The module with the ACS725 current sensor with a direct current measuring range up to 10 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020616
zł52.62
24h
Available quantity: 5
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.94
24h
Available quantity: 50
Available
Available
This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034
zł35.65
24h
Available quantity: 4
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł98.45
24h
Available quantity: 2
Available
Module with ACS723 current sensor with a measuring range of AC and DC ± 5 A. It communicates via an analog interface. SparkFun SEN-13679
zł48.54
24h
Available quantity: 4
Available
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
zł47.71
24h
Available quantity: 5
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł81.72
24h
Available quantity: 3
Available
Module with INA228 sensor designed for power monitoring. It allows you to measure voltages up to 85 VDC and currents up to 10 A. It uses a 20-bit ADC converter, which guarantees very precise and accurate measurements available via the I2C bus. Adafruit 58332
zł83.06
Delivery date unknown
No product available!
ACS714 Current Sensor Carrier -30 to +30A
zł53.03
24h
Available quantity: 2
Available
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł53.19
24h
Available quantity: 2
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł8.00
6 weeks
No product available!
Module with bi-directional current sensor based on the INA226 system. It allows you to measure current and power, works with a voltage of 0-36 V. It has an I2C interface.
zł29.90
24h
Available quantity: 28
Available
ACS711EX Current Sensor Carrier -31A to +31A
zł18.88
6 weeks
No product available!
ACS724LLCTR-10AB current sensor module with a DC and AC measurement range from -10 to +10 A. It communicates via an analog interface. Pololu 4043