Pololu Carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F Sensors
This tiny carrier board makes it easy to integrate the Sharp GP2Y0D810Z0F and GP2Y0D805Z0F digital distance sensors into your project by providing all of the required external components, an LED for feedback about the output state, and 0.1"-pitch, three-pin interface to the sensor.
![]() |
The GP2Y0D805 and GP2Y0D810 are Sharp’s smallest and fastest distance sensors, and our tiny carrier board for these sensors includes all of the external components required to make them work. With a sample rate of almost 400 Hz and a sensing distance to 5 cm (GP2Y0D805) or 10 cm (GP2Y0D810), this sensor provides an attractive alternative to shorter-range LED-phototransistor reflectance pairs and longer-range but slower sensors such as the Sharp GP2Y0A21YK0F analog distance sensor.
However, these sensors require external components and have a non-standard 1.5 mm pitch, which can make them difficult to integrate into projects based on a 0.1" pitch. This carrier board includes these components and provides a 0.1"-pitch, three-pin interface: ground, power, and output.
Note: this product requires a Sharp GP2Y0D810Z0F or GP2Y0D805Z0F sensor (sold separately). We also offer a version of this carrier board assembled with a GP2Y0D810Z0F and a version assembled with a GP2Y0D805Z0F.
![]() |
| Pololu carrier with Sharp GP2Y0D810Z0F digital distance sensor 10cm. |
|---|
You will need to solder the sensor to the carrier board so that the solder connections are made on the component-side of the board and the sensor package presses against the component-free side of the board. Once the sensor is soldered in, the Pololu carrier board lets you interface with the GP2Y0D810 or GP2Y0D805 sensor using a three-pin 0.100" connector, such as the included 3×1 straight male header strip and 3×1 right-angle male header strip. You can connect to these pins with a servo cable or with a custom-made cable using pre-crimped wires and a 3×1 crimp connector housing.
The square pad is ground, the middle pad is VIN (2.7 – 6.2 V), and the remaining pad is the sensor output, OUT. Depending on your power source, you might notice an increase in performance by placing a large (>10 uF) capacitor between power and ground somewhere near the sensor.
A red LED on the back of the PCB lights when the output is low, indicating that the sensor is detecting something. If so desired, you can disable this LED by cutting the trace between it and the OUT pin where it is marked on the silkscreen or by desoldering the LED.
The GP2Y0D810Z0F and GP2Y0D805Z0F have an optional enable input that can be used to put the sensor into low-power mode. The Pololu carrier board connects this input to Vcc so that the sensor is always enabled, but you can solder a wire to the pad labeled “enable” on the back of the PCB if you want control over this input. Note that you will need to cut the trace that connects the enable line to Vcc on the PCB if you want to be able to disable the sensor. This trace is marked on the silkscreen, and there is a caret that indicates where we suggest you make the cut.
The carrier board has a 0.086" mounting hole for a #2 screw. You can make the module more compact by cutting or grinding off this portion of the PCB if you do not need the mounting hole.
![]() |
| Pololu carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F sensors schematic diagram. |
|---|
![]() |
Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
![]() |
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
![]() |
Sharp GP2Y0D805Z0F Digital Distance Sensor 5cm |
Data sheet
Manufacturer
Responsible person
Distance Measuring Sensor Unit Digital output (100 mm) type, voltage 2.7V-6.2V, Sharp, RoHS
No product available!
Ultrasonic ToF (time-of-flight) rangefinder with a range of 4 cm to 1.2 meters. The sensor is able to simultaneously measure the range of several objects in its field of view. Communicates via I2C. SparkFun SPX-17271
No product available!
The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-6180A1 board with the VL6180 distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-6180A1
Module with a digital distance sensor with a range of up to 25 cm. It has a digital output that goes low when an object is detected. Pololu 4066
Module with a digital distance sensor with a range of up to 50 cm. It has a digital output that goes low when an object is detected. Pololu 4067
Module with a digital distance sensor with a range of up to 100 cm. It has a digital output that goes low when an object is detected. Pololu 4069
Module with a digital distance sensor with a range of up to 200 cm. It has a digital output that goes low when an object is detected. Pololu 4077
Module with a distance sensor with a range of up to 130 cm. It has a digital output that generates a pulse with a width proportional to the measured length. Pololu 4071
No product available!
Module with a distance sensor with a range of up to 300 cm. It has a digital output that generates a pulse with a width proportional to the measured length. Pololu 4079
ToF laser rangefinder. It enables detection of many objects, has a field of view of about 25 ° and is able to detect objects at a distance of up to 5 m. Communicating via the I2C interface. Pololu 3416
Module with the 3-channel distance sensor OPT3101. The sensor has a range of up to 1 m, a wide viewing angle of up to 180° and communicates via the I2C interface. Pololu 3412
Module with the 3-channel distance sensor OPT3101. The sensor has a range of up to 1 m, a wide viewing angle of up to 180° and communicates via the I2C interface. Pololu 3680
Module with an integrated proximity and ambient light sensor based on the VCNL4040 system. It can detect obstacles in the range of 0 to 20 cm. It communicates via the I2C bus. Adafruit 4161
ToF VL53L0X distance sensor module designed for M5Stack sets. It allows you to measure distances up to 2 m and communicates via the I2C interface. M5Stack U072
Ultrasonic distance sensor module with a range of up to 720 cm. It communicates via UART, I2C or PWM interface. It is compatible with 3.3V or 5V devices. GY-US12V2
ToF distance sensor module based on the VL6180X system. It offers a range of 2 to 50 cm and communicates via the I2C interface. TOF050C
Module with ToF distance sensor based on the VL53L0X system. It offers a range of 3 to 200 cm and communicates via the I2C interface. TOF200C
Pololu Carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F Sensors