Gravity: Analog Signal Isolator - analog signal isolator
ID: 566119
5902186313088
zł88.25
Tax included
zł71.75 tax excl.
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
Description
Gravity: Analog Signal Isolator is a module that prevents electrical interference between sensors. In many cases, to ensure reliable operation of the sensors, isolation of the sensors in the device is required, because they can interfere with each other and will not perform correct measurements. The insulating module allows to separate the sensors in the device and increase the stability and reliability of operation. The module has a built-in 5V power supply, so you do not need to connect an external, additional power source for the sensor. The module has been equipped with a Gravity connector allowing easy connection of sensors to the module. The tile can be used, for example, in a multi-parameter water quality monitoring system.
In order for the module to work properly, it should be noted that:
- module power supply should be stable to achieve stable readings
- the current consumed by the sensors should not exceed 170 mA
- do not short-circuit the mass field on the sensor side and the MCU module (they are isolated)
- it is necessary to ensure heat dissipation from the module, because it can give off large amounts of heat
properties
- Response time: 4 sec
- Gravity PH2.0-3P connector
- Power consumption (without load): 75mA
- Non-insulated connector (MCU connector):
- Supply voltage: 5.0 ± 0.1 V
- Analog output: 0 ... 5.0 V
- Insulated connector (SEN connector)
- Output voltage: 5.0 ± 0.2 V
- Analog input: 0..5,0 V
- Power supply: 5 V
- Dimensions: 42 x 32mm
Included
- Gravity Module: Analog Signal Isolator
- 2 x Gravity Connection Cable (PH2.0-3P Cable)
566119
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Single-Channel High Speed 10MBit/s Logic Gate Optocouplers, DIP8, Fairchild Semiconductor, RoHS
zł0.98
24h
Available quantity: 8
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.92
24h
Available quantity: 4
Available
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
Other products in the same category (16)
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
zł112.72
24h
Available quantity: 2
Available
Gravity: Digital Peristaltic Pump is a peristaltic pump with a controller and a connector compatible with modeling servos. The set is powered by 5 ... 6 V. DFRobot DFR0523
zł111.23
24h
Available quantity: 3
Available
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
zł11.01
24h
Available quantity: 2
Available
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
zł7.54
24h
Available quantity: 3
Available
Digital orientation sensor module. DFRobot DFR0028
zł7.52
24h
Available quantity: 2
Available
Module with 5 A 250 VAC relay. DFRobot DFR0017
zł12.63
24h
Available quantity: 3
Available
Fan module with DC motor, propeller and connection cable. DFRobot DFR0332
zł29.22
24h
Available quantity: 3
Available
LM35 analog temperature sensor module for Arduino. DFRobot DFR0023
zł15.88
4 weeks
No product available!
PIR motion sensor module for Arduino and Raspberry Pi. DFRobot SEN0018
zł19.46
24h
Available quantity: 5
Available
Micro:Mate is an expansion board for the micro: bit development module. It provides six 3-pin connectors with I/O outputs, a 3.5mm audio jack connector and is powered from a 5V microUSB connector. DFRobot DFR0518
zł30.90
4 weeks
No product available!
VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245
zł65.19
4 weeks
No product available!
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
4 weeks
No product available!
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024
zł24.44
24h
Available quantity: 4
Available
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
zł23.70
24h
Available quantity: 1
Available
Gravity: Digital IR Receiver Module is a module with an IR receiver operating at 38kHz. The module is supplied with 5V voltage. DFRobot DFR0094
zł20.97
24h
Available quantity: 1
Available
Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440
zł10.97
24h
Available quantity: 2
Available
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504