KAmodPCAL6408 - 8-channel I2C expander module
ID: 586091
5906623432837
zł16.90
Tax included
zł13.74 tax excl.
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Description
KAmodPCAL6408 is an 8-bit I/O expander with I2C control. It has 8 GPIO outputs/inputs. The module has the ability to select the address of the system, so that 2 such modules can be connected to one bus. The board is equipped with a standard Pmod I2C connector and a KAMAMI connector, allowing for easy connection of the module to the development kits. Thanks to its small dimensions, the product can be used in many development projects, while the Pmod straight-through connector allows you to connect boards in rows.
Properties
- NXP PCAL6408A chip
- 8 programmable inputs / outputs
- I2C bus
- Programmable interrupt output
- Ability to select chip address (0x20 or 0x21)
- Pass-through connector compatible with Pmod standard, allows for serial connection of Pmod I2C modules
- Connector compatible with KAMAMI standard
- Built-in pull-up jumpers on I2C bus lines
- Built-in jumper for connecting INT line of system to INT line of Pmod connectors
- Built-in I2C address selector
- Possibility to power supply with voltage in the range 1.7-5.5 V through the Pmod connector and 1.8-5.5 V through the KAMAMI connector
- Mounting holes 2.5mm in diameter
- Dimensions: 61.2 x 20.3 x 10mm
586091
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Other products in the same category (16)
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
zł19.90
24h
Available quantity: 431
Available
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 370
Available
KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.
Regular pricezł229.00zł206.10
24h
Available quantity: 47
Available
Module with L3G4200D (3-axis gyroscope with digital output)
zł34.90
24h
Available quantity: 2
Available
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
zł37.90
24h
Available quantity: 406
Available
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
zł39.90
24h
Available quantity: 100
Available
Available
ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.
zł24.90
24h
Available quantity: 318
Available
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
zł99.00
24h
Available quantity: 36
Available
KAmodPCA9533 is a module with LED driver from NXP. The module allows you to control the brightness of 4 LEDs using programmable PWM signals (with a frequency from 0.591 Hz to 152 Hz). I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector
zł21.89
24h
Available quantity: 214
Available
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
zł27.48
24h
Available quantity: 123
Available
Available
zł5.90
24h
Available quantity: 480
Available
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
zł19.90
24h
Available quantity: 462
Available
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.
zł37.90
24h
Available quantity: 3
Available
Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer
zł81.52
24h
Available quantity: 83
Available
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.