Module with an analog light sensor. It consists of a photoresistor and a LED that facilitates checking the range of values returned by the sensor. The sensor detects the change in light intensity and generates an analog signal proportional to this change. The module is equipped with a Gravity connector. It will be used in projects such as automatic lamp. The user manual and sample programs are available on the Wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Set of 10 cables, 30 cm long, for analog sensors compatible with the Gravity standard. DFRobot FIT0031
No product available!
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Detection range from 10 to 20 cm, communication via I2C. SparkFun SEN-12787
modTSL2561 is a module containing a light sensor TSL2561; communication with the system takes place using the I2C bus
No product available!
The module allows measuring the light around the sensor. The measuring range is in the range 1 - 65535 LUX, and communication takes place using the I2C bus. modBH1750 (GY-302)
SEN0162 This UV Sensor with GUVA-S12SD chip is suitable for detecting the UV raditation in sunlight. It can be used in UV Index Monitoring, DIY project, UV-A Lamp Monitoring, Plants growing Environmental monitoring...etc.
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
The set contains: MQ-5 Gas Sensor, Color Sensor, Flame Sensor, Hall Sensor, Infrared Reflective Sensor, Laser Sensor, Moisture Sensor, Rotation Sensor, Sound Sensor, Temperature-Humidity Sensor, Tilt Sensor, UV Sensor, Liquid Level Sensor. Modules compatible with Arduino
Color Sensor, complete color detector
Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
No product available!
Module with ultraviolet (UV) sensor based on the GUVA-S12D system. It allows measurement of radiation with a wavelength in the range from 240 to 370 nm. The module has a connector in accordance with the Grove standard. Seeed Studio 101020043
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
Module with digital light sensor TSL2561. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020030
UV Sensor with response spectrum: 200nm-370nm
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228
Module with an analog light sensor. It consists of a photoresistor and a LED. Equipped with a Gravity connector. DFRobot DFR0022