

zł25.26 tax excl.
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353
Module with an external counter TPL5110, which allows you to turn on the project after a set time and save energy if the device does not need to run all the time. It allows, for example, after reading measurements from sensors, sending data and storing them in the recorder, to turn off the power and then turn it on again, for example, after 1h.
The TPL5110's delay is configurable via resistors. Operation is facilitated by a six-way DIP switch, which allows you to select one of five pre-installed resistors. A sixth switch is attached to a pad that allows you to add your own PTH (or SMD) resistor. The delays associated with the pre-installed settings are labeled on the bottom of the board for quick configuration. In addition, more than one switch can be selected to connect resistors in parallel (up to 26 options, not including a custom resistor).
The Nano Power Timer supports voltages from 1.8 V to 5.5 V and currents up to 1.1 A. Timing configuration options range from 100 ms to two hours (preconfigured settings from 30s to 2h). There is a button on the board that will allow the user to quickly override the delay, so you can turn on your project at any time. Full documentation and usage examples are available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Li-Po battery 3.7V / 220mAh. Connector + JST-BEC 2,54, 2 pins, PCM protection, cable length 150mm. Akyga LP402036
No product available!
Li-Po battery with a rated voltage of 3.7 V and a capacity of 400 mAh, equipped with a PCM protection and a 2.5 JST-RCY connector. Akyga LP403035
No product available!
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
No product available!
GPS module with 72-channel GNSS NEO-M8P-2 receiver. It can receive data from GPS, GLONASS and BeiDou systems. It has USB, UART, I2C and SPI interfaces. RTK and high accuracy up to 25mm. SparkFun GPS-15005
No product available!
Module with NEO-F9P GNSS receiver. It allows you to track signals from several satellite systems, including GPS, GLONASS, Galileo and Beidou, and offers accuracy of up to 10 mm using an RTK base station. It offers five communication ports: USB type C, UART1, UART2 for RTCM, I2C and SPI reception and Qwiic connectors. SparkFun GPS-23288
No product available!
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
The expansion module is designed for micro:bit board. Controller: bit offers a fully functional controller module with a design based on a classic Nintendo controller. SparkFun DEV-16129
Module with transparent OLED display. It has several display areas with different colors. I2C communication. SparkFun LCD-15079
No product available!
Sound module supported by I2C interface, which allows to generate sound signals in simple projects thanks to Qwiic system and ATtiny84 microcontroller. With support of Arduino libraries, users can control volume, frequency and duration of sound, which makes it ideal for applications such as alarms or signals in robots. SparkFun BOB-24474
No product available!
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396
Module with a satellite data receiver for transmission with L-band correction. It can be configured for use with various correction services to achieve centimeter-level positioning accuracy. SparkFun GPS-19390
No product available!
GPS module with GNSS receiver ZED-F9P. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. It has USB, UART, I2C and SPI interfaces. RTK and high accuracy up to 10 mm. SparkFun GPS-16481
No product available!
Module dedicated to projects related to air quality monitoring. It uses the popular ENS160 and BME280 chips and provides a variety of environmental data such as Air Quality Index (AQI), TVOCs levels, CO2 equivalent (eCO2), atmospheric pressure, humidity and temperature. It communicates via the I2C interface and offers two Qwiic connectors. SparkFun SEN-22858
Module with PIR EKMB1107112 motion sensor, power consumption in standby mode up to 1 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17375
No product available!
Module with digital barometer BMP384. It enables pressure measurement in the range from 300 to 1250 hPa with 24-bit resolution and communicates via I2C or SPI. SparkFun SEN-19662
Flexible 4-core cable, 500 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17257
No product available!
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16916
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353