Gravity: Analog Heart Rate Monitor Sensor (ECG) - heart rate monitor for Arduino
ID: 562582
zł104.40
Tax included
zł84.88 tax excl.
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Gravity: Heart Rate Monitor Sensor (ECG) is a sensor that monitors electrical heart activity. Data on myocardial activity are sent in the form of analogue data in the range of 0 ... 3.3 V. The module's power supply should be in the range of 3.3 ... 6 V. Due to the large noisy data on heart activity, the module AD8232 chip, which provides clear signals for PR and QT intervals. Special electrodes for measurements are included in the set.
The module is adapted for use with Arduino sets and other evelution plates. Thanks to the "Serial Plotter" tool built into the Arduino IDE, the user can easily obtain an electrocardiographic curve (ECG) from analog data.
Attention!
This product is not a medical device and is not intended to diagnose or treat from a medical point of view.
properties
- Analog output: 0 ... 3.3 V
- Connector type: Gravity PH2.0-3P
- Power consumption less than 10 mA
- Supply voltage: 3.3 ... 6 V (recommended 5V)
- Dimensions: 35 x 22 mm
Included
- Heart activity monitoring sensor
- Three-lead electrode lead
- Electrodes x 6
- Gravity PH2.0-3P cable
562582
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł113.90
24h
Available quantity: 70
Available
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
zł94.70
24h
Available quantity: 4
Available
Available
Available
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
zł83.95
24h
Available quantity: 2
Available
Other products in the same category (16)
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
6 weeks
No product available!
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
zł19.45
24h
Available quantity: 3
Available
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
zł62.77
24h
Available quantity: 2
Available
Available
Sensor module for electromyography (EMG). Allows muscle activity to be studied and used to control devices. SparkFun DEV-21265
zł219.00
6 weeks
No product available!
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
zł289.00
6 weeks
No product available!
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
zł120.98
24h
Available quantity: 6
Available
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Available
Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.
zł8.30
6 weeks
No product available!
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
zł160.67
6 weeks
No product available!
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
zł14.90
24h
Available quantity: 5
Available
Muscle Sensor Surface EMG Electrodes allow you to control your projects with your muscles. Adafruit 2773
zł29.19
4 weeks
No product available!
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
zł94.70
24h
Available quantity: 4
Available
Module with a sensor for measuring the heart rate PAH8001EI-2G. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020082
zł158.45
6 weeks
No product available!
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
zł261.94
24h
Available quantity: 3
Available
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213