Module with 8 SSR relays with a load of up to 3 A and 10 GPIO pins that can operate in the analog input mode. It enables the switching of high-power devices over an Ethernet interface controlled by a built-in, easy-to-use network interface or any popular terminal emulator that supports the TELNET protocol. Each 8-channel Ethernet Solid State Relay Module is shipped with a unique MAC address. These devices also support assigning and retrieving custom identification strings that can be used to identify individual devices when a large number of boards are connected to the same network. All relay terminals are available on screw terminals, which makes it easy to connect external devices.
Compared to electromechanical relays, SSRs are based on semiconductor devices (transistors and thyristors) and offer a faster switching speed. Relays used in the module can control alternating current. The module will be used in home automation projects, lighting systems and garden equipment. Full documentation is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the Ethernet interface. Numato Lab 8ETHSSR001-DC
No product available!
Module with 8 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC80001-DC
No product available!
Module with 8 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC80001-AC
No product available!
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the USB interface. Numato Lab SSR80001-DC
No product available!
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the USB interface. Numato Lab SSR80001-AC
No product available!
Module with 16 relays and 8 analog inputs. Communicates via the WiFi wireless interface. Numato Lab WFRL160001
No product available!
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
Module with 16 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL160001
16-channel PoE module with relays allowing you to connect your PC to other electronic circuits via the network. It does not need a separate cable for power and data transmission. It can be controlled via a simple web interface or Telnet. Numato Lab NLRP1002-A
No product available!
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
Module with 16 relays 12 V with a maximum switching current of 7 A. Numato Lab RL40003
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
No product available!
Crowtail-TPL5111 Reset Enable Timer is a module for energy-efficient power control of devices in battery-powered projects. It offers six programmable time intervals and an automatic reset mode, supporting the design of low-power circuits.
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
Module with 32 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001
No product available!
Module with 2 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL20001
4-channel switch module with a maximum voltage of 16 V and a current of 2 A based on a MOSFET transistor. It is controlled by digital inputs. It is equipped with a screw connection and status LEDs. Adafruit 5757
No product available!
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
No product available!
Module with a relay and WiFi communication. Compatible with ESP-01 or ESP-01S
Module with 8 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC80001-DC
No product available!
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the Ethernet interface. Numato Lab 8ETHSSR001-AC