Crowtail – Dual Coil Latching Relay Module 2.0 – 2-channel latching relay, 5 V, 3 A, low-power
ID: 1201696
5902186332027
zł16.85
Tax included
zł13.70 tax excl.
Crowtail – Dual Coil Latching Relay Module 2.0 is an energy-efficient dual-channel latching relay that retains its state after power loss. Intended for use in automation systems, remote control, and battery-powered projects.
Description
The Crowtail – Dual Coil Latching Relay Module 2.0 is a module with a dual-coil latching (bistable) relay that retains its last state (on/off) even after the power is disconnected. The state changes by applying a rising or falling pulse — it does not require continuous coil power. This makes the module ideal for use in low-power circuits, automation, remote control, and emergency power and communication systems. Its high switching capacity and compatibility with the Crowtail system allow easy integration with microcontrollers.
Properties
- Relay type: latching, dual coil (2 Form C)
- Operating voltage: 5 V
- Maximum switching voltage: 35 V AC / 35 V DC
- Maximum switching current: 3 A
- Maximum set/reset voltage: 4.0 V DC
- Set time: max. 4.5 ms
- Reset time: max. 3.5 ms
- Sensitivity: 150 mW
- Switching capacity: 60 W / 125 VA
- Epoxy-sealed housing – resistant to wave soldering and cleaning
- Compatibility with 16-pin IC socket
- Dimensions: 50.0 × 35.0 × 14.3 mm
Included
- Crowtail – Dual Coil Latching Relay Module 2.0 module x1
- Crowtail 4-pin cable x1
1201696
Data sheet
- Output current
- 3A
- Number of channels
- 2
- Executive element
- Impulse relay
- Coil voltage
- 5 VDC
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
zł51.94
24h
Available quantity: 1
Available
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO
zł8.54
4 weeks
No product available!
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
zł22.40
4 weeks
No product available!
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
zł21.01
4 weeks
No product available!
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895
zł52.00
24h
Available quantity: 1
Available
Adafruit FeatherWing module with snap relay. It allows you to control high-power components using a microcontroller. It allows switching current to 2A (at 40VAC or 30VDC) and voltage up to 250VAC. Adafruit 2923
zł40.74
24h
Available quantity: 1
Available
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815
zł52.71
24h
Available quantity: 1
Available
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
zł49.73
24h
Available quantity: 1
Available
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
zł16.86
24h
Available quantity: 5
Available
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł50.41
24h
Available quantity: 2
Available
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
zł44.58
24h
Available quantity: 1
Available
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
zł9.67
24h
Available quantity: 39
Available
The module with the HLS8-T73 relay with a load up to 5 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020005
zł13.80
24h
Available quantity: 7
Available
The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435
zł25.89
4 weeks
No product available!
Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473
zł20.07
4 weeks
No product available!
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
zł8.84
24h
Available quantity: 118
Available
Crowtail – Dual Coil Latching Relay Module 2.0 is an energy-efficient dual-channel latching relay that retains its state after power loss. Intended for use in automation systems, remote control, and battery-powered projects.