- New
zł11.44 tax excl.
Makerbase MKS 3MOS expansion module for independent control of three fans in 3D printers. Features three MOSFET outputs, each supporting a current below 1 A, and operates with a supply voltage of 12 V to 24 V DC. Installs into an available, compatible StepStick motor driver socket and uses ENABLE, STEP and DIR signals for fan control. Requires appropriate configuration of the mainboard firmware. Makerbase MKS 3MOS
The MKS 3MOS expansion module from Makerbase is designed to control three additional fans in 3D printers equipped with compatible mainboards. The board features three independently controlled MOSFET outputs, enabling individual fan switching and speed adjustment using PWM signals. The module installs directly into an available StepStick-compatible stepper motor driver socket, allowing the mainboard's existing control lines to operate additional cooling circuits. Applications include expanding print cooling, heatsink cooling and other cooling systems in 3D printers.
The MKS 3MOS operates with a DC supply voltage of 12 V to 24 V. Each of the three outputs supports a current load below 1 A. The module draws fan power from the motor driver's VMOT supply line, so the output voltage corresponds to the mainboard's motor supply voltage. For example, when VMOT operates at 24 V, the connected fans must be rated for 24 V or powered through an additional voltage-reducing circuit. Fan control uses low-side switching, with the negative supply connection of each fan switched by a MOSFET while the positive connection remains connected to the supply line.
The three channels are controlled using ENABLE, STEP and DIR signals, normally available in the stepper motor driver socket. FAN1 uses ENABLE, FAN2 uses STEP, and FAN3 uses DIR. This arrangement enables independent control of three fans after assigning the relevant pins in the mainboard firmware. The module provides three two-pin fan connectors with polarity markings. When connecting fans, the positive and negative power wires must be connected according to the connector markings.
The module is designed for compatible Makerbase mainboards, including MKS Robin, MKS Gen-L, MKS SGEN-L, MKS Monster8 and MKS TinyBee, provided that a suitable unused stepper motor driver socket is available. Supporting the additional channels requires firmware configuration, for example in Marlin, by assigning the ENABLE, STEP and DIR signals to fan outputs. Depending on the firmware configuration, fan operation can be controlled using G-code M106 commands specifying the fan number and PWM value. Before installation, the socket pinout, VMOT voltage and power supply capacity for the connected loads must be checked.
The MKS 3MOS PCB measures 20.32 x 15.24 mm and is designed for installation in a compact stepper motor driver socket. No separate signal cable is required because the connection to the mainboard is made through the module's pin headers. The printer power supply must be completely disconnected before installation. After mounting, the module orientation and output configuration should be checked. The MKS 3MOS does not function as a stepper motor driver and occupies one driver socket, which can no longer be used to control a stepper motor simultaneously.
Data sheet
Module with 2 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital inputs. Seeed Studio 103020134
Module with relay SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital input. Seeed Studio 103020137
No product available!
The module is equipped with three 5A / 250VAC relays controlled by digital outputs. Relay contacts are led out to ARK screw terminals. Designed to work with NVIDIA Jetson Nano. Waveshare 3-CH Relay for Jetson Nano
No product available!
Extension module designed for home automation projects compatible with Raspberry Pi. The board is equipped with a 24 V 2 A relay, three buffer inputs, three sink outputs and three analog inputs with a working range up to 24 V. Pimoroni PIM487
Extension module compatible with Raspberry Pi. The board is equipped with three 24 V 2 A relays, three buffer inputs, three sink outputs and three analog inputs with a working range up to 24 V. Pimoroni PIM213
Switch module with a maximum voltage of 40 V and a current of 10 A, based on a MOSFET transistor, HT0740 driver and I2C expander. It has a screw connection and a status LED. Pimoroni PIM455
8-channel module with relays designed to work with the Raspberry Pi Pico. Has built-in power isolation. Perfect for industrial applications. Waveshare Pico-Relay-B
Industrial module with 4 relays with a load of up to 10 A. It uses the Modbus RTU protocol and the RS485 or RS232 communication interface. DFRobot FIT0827
No product available!
5V relay module with IR receiver. Comes with a remote control
Module with a 12 V relay and a timer. It enables the implementation of delayed switching on or off of the circuit with the possibility of time adjustment
Board with the WiFi ESP-12F (ESP8266) module and a 5 V relay. Equipped with an AC adapter
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21284
The module is dedicated to home automation based on the Raspberry Pi. It allows you to control two devices 250VAC/7A or 30VDC/10A, providing isolation with an optocoupler. SB Components 21932
8-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. With LCD 4,3" display. SB Components 21871
8-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 21871
Module with the SLA-05VDC-SL-C relay with a maximum load of 30 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020012
Makerbase MKS 3MOS expansion module for independent control of three fans in 3D printers. Features three MOSFET outputs, each supporting a current below 1 A, and operates with a supply voltage of 12 V to 24 V DC. Installs into an available, compatible StepStick motor driver socket and uses ENABLE, STEP and DIR signals for fan control. Requires appropriate configuration of the mainboard firmware. Makerbase MKS 3MOS