

An executive module with a transistor
Description
The executive module with transistor is used to control systems operating with voltage or current, different, often larger than that used by the control system.
Control systems often have limitations related to voltage or current. If we want to connect, for example: an LED strip supplied with +12 V voltage to the microcontroller, we can not do it directly, due to the voltage and current limitation of the microcontroller. In this case, the actuation systems are used for control. We connect the SIG (IN) control signal (from +4 V to +5 V) to the module and the voltage we want to control, between the VCC or VIN output (up to +12 V), and the GND ground (see "Example connection").
Attention!
The standard configuration is a compact jumper Z1. This means that the VCC and VIN outputs are connected to each other. The supply voltage to be at the module output should be connected to the VCC or VIN output.Technical data:
Set contains:
No product available!
The 24 V relay module with adjustable delay time offers a practical solution for AC/DC load control in automation and electronics applications
No product available!
Module with 32 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001-24
No product available!
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO
No product available!
Module with 64 relays and 8 GPIO pins and 6 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1003-A
No product available!
Adafruit FeatherWing module with snap relay. It allows you to control high-power components using a microcontroller. It allows switching current to 2A (at 40VAC or 30VDC) and voltage up to 250VAC. Adafruit 2923
Module with 16 relays 12 V with a maximum switching current of 7 A. Numato Lab RL40003
No product available!
Module with 32 relays and 8 analog inputs. Communicates via the WiFi wireless interface. Numato Lab WFRL320001
No product available!
2-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 14088
No product available!
The module is dedicated to home automation based on the Raspberry Pi. It allows you to control two devices 250VAC/7A or 30VDC/10A, providing isolation with an optocoupler. SB Components 21932
Module with 8 digital inputs and 4 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8024ADAM
No product available!
Module with 8 relays 12 V with a maximum switching current of 7 A. Communicates via the USB interface. Numato Lab RL80001
No product available!
Module with 32 12 V relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL320001
Module with 4 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC40001-DC
No product available!
Module with SSR relay with a load of up to 3 A. It communicates via the USB interface and does not require additional power supply. Numato Lab SSRP20001-DC
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)