

zł25.26 tax excl.
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Module with an external counter TPL5110, which allows you to turn on the project after a set time and save energy if the device does not need to run all the time. It allows, for example, after reading measurements from sensors, sending data and storing them in the recorder, to turn off the power and then turn it on again, for example, after 1h.
The TPL5110's delay is configurable via resistors. Operation is facilitated by a six-way DIP switch, which allows you to select one of five pre-installed resistors. A sixth switch is attached to a pad that allows you to add your own PTH (or SMD) resistor. The delays associated with the pre-installed settings are labeled on the bottom of the board for quick configuration. In addition, more than one switch can be selected to connect resistors in parallel (up to 26 options, not including a custom resistor).
The Nano Power Timer supports voltages from 1.8 V to 5.5 V and currents up to 1.1 A. Timing configuration options range from 100 ms to two hours (preconfigured settings from 30s to 2h). There is a button on the board that will allow the user to quickly override the delay, so you can turn on your project at any time. Full documentation and usage examples are available on the product page.
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Li-Po battery 3.7V / 220mAh. Connector + JST-BEC 2,54, 2 pins, PCM protection, cable length 150mm. Akyga LP402036
No product available!
Li-Po battery with a rated voltage of 3.7 V and a capacity of 400 mAh, equipped with a PCM protection and a 2.5 JST-RCY connector and socket. Akyga LP403035
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
Mini module with ToF VL53L5CX sensor with a matrix of 64 pixels and a range of up to 4 m. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-19013
Module with a capacitive touch sensor based on the CAP1203 chip. There are three touch panels on the board that can be used as separate sensors (pins CS1, CS2, CS3) or as a touch slider. I2C communication. SparkFun SEN-15344
SparkFun Qwiic kit. Contains 10 wires of different lengths and tips. It allows you to connect Qwiic modules to a programming platform or to a prototype board. SparkFun KIT-15081
Module with a voltage level converter 3.3 V - 5 V intended for use in the Qwiic system. It has a built-in Step Up converter providing power supply with a voltage of 5 V and a current of up to 100 mA. SparkFun SPX-17238
No product available!
Module with a cryptographic coprocessor based on the ATECC508A system. It allows you to add strong authentication security to an IoT node or embedded system. I2C communication. SparkFun DEV-15573
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16397
No product available!
GPS module with GNSS receiver ZED-F9P. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. It has USB, UART, I2C and SPI interfaces. RTK and high accuracy up to 10 mm. SparkFun GPS-15136
No product available!
Module with 4 relays controlled by the I2C interface. Each relay can switch currents up to 40 A at 28-380 V AC. SparkFun KIT-16833
Module with 20x4 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16398
No product available!
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16917
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Air speed sensor module based on the FS3000-1005 chip. The board is equipped with Qwiic connectors. SparkFun SEN-18377
LPS28DFW absolute pressure sensor module. The chip features a wide measurement range of 260 to 1260 hPa or 260 to 4060 hPa and a high accuracy of 0.5 hPa. It communicates via an I2C interface. SparkFun SEN-21222
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-18565
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353