- Out-of-Stock
The USB-FDCAN converter is a device that enables communication between the computer and the CAN (Controller Area Network). It supports the CAN FD standard and is equipped with a Microchip MCP2542FD transceiver. FDCAN USB converter
The USB-FDCAN converter is a device that enables communication between the computer and the CAN (Controller Area Network). It supports the CAN FD standard, which means it can transfer data at higher speeds than traditional CAN networks. It is equipped with a Microchip MCP2542FD FD CAN transceiver, which is responsible for the physical layer of the CAN network and provides the necessary connection between the device and the network. The converter can support baud rates up to 8 Mbps and provides hardware frame filters that allow selective frame reception, which is useful for large CAN networks. The device can run on Windows, however, a Windows Subsystem for Linux (WSL) environment may be required for full functionality.
Manufacturer
Responsible person
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CCP-MUSB2-AMBM-W-1M
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-BK
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
No product available!
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
No product available!
Patchcord UTP 5E Ethernet cable with a length of 25 cm - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 1.5 m - black, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 1.5 cm - gray, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 3 m - black, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 5 m - blue, with 2xRJ45 connectors
No product available!
The USB-FDCAN converter is a device that enables communication between the computer and the CAN (Controller Area Network). It supports the CAN FD standard and is equipped with a Microchip MCP2542FD transceiver. FDCAN USB converter