.png)
- Out-of-Stock
Turnigy Multistar 45 Amp Multi-rotor Brushless ESC 2-6S
ID: 224479
Turnigy Multistar 45 A - Brushless motor speed controller for 2-6S multirotors (HK25366)
Turnigy Multistar 45 A - Brushless motor speed controller for 2-6S multirotors (HK25366)
MultiStar ESCs speed controllers offer high quality and are also inexpensive! Designed for simple structures and easy to assemble controllers, they proved to be ideal for multirotors.
The controller is characterized by smooth development of power without limiting power. Security is also not neglected by equipping the controller with LVC (Low Voltage Cut-off), overload protection in the event of a motor lock, protection in the event of a lack of control signal and safe arming.
Multistar controllers are factory equipped with Gold connectors adapted to the current range of the regulator.
Functions:
• Linear power control
• Quick reaction
• Atmel microcontroller
• Protection in the event of engine blockage
• Protection in the event of signal loss
• Safe startup
• Ability to control 480 Hz + signals (up to 499 Hz)
• Possibility to use the programming card
Specification:
Continuous current: 45 A
Power supply: 2-6S Lipo
BEC: Yes
BEC voltage: 5.5 V / 6 A
PWM: 8 KHz
Max RPM: 240000 rpm for a 2-pole brushless motor
PCB size: 50mm x 30mm
Power connector: male 4.0 mm
Motor connection: female 4.0 mm
Weight: 58 g
PRODUCT ID: 9351000005
Download
| Customer files | ||
| Manual - Turnigy Multistar Brushless ESC | 2384kb | |
224479
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Plastic holder that could fit all the boards with Arduino UNO size (68,6 mm x 53,4 mm). Contains 5 pieces in different colours. A000018
Delivery date unknown
No product available!
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Turnigy Multistar 45 A - Brushless motor speed controller for 2-6S multirotors (HK25366)