- Out-of-Stock
X-NUCLEO-IKS01A1
ID: 234919
MEMS and environmental sensor expansion board for STM32 Nucleo
X-NUCLEO-IKS01A1
MEMS and environmental sensor expansion board for STM32 Nucleo, STM, RoHS
The X-NUCLEO-IKS01A1 is a MEMS inertial and environmental sensor evaluation board system. It is compatible with the Arduino UNO R3 connector layout, and is designed around STMicroelectronics’ LSM6DS0 3-axis accelerometer + 3-axis gyroscope, the LIS3MDL 3-axis magnetometer, the HTS221 humidity sensor and the LPS25H pressure sensor. The X-NUCLEO-IKS01A1 interfaces with the STM32 microcontroller via the I2C pin, and it is possible to change the default I2C port.
Features:
- LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
- LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
- LPS25H: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
- HTS221: capacitive digital relative humidity and temperature
- DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
- Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
- Compatible with STM32 Nucleo boards
- Equipped with Arduino UNO R3 connector
X-NUCLEO-IKS01A1 with STM32 Nucleo Board
Contents:
- MEMS and environmental sensor expansion Shield (X-NUCLEO-IKS01A1)
234919
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
PS/2 adapter with a connector for connecting a keyboard and a mouse via USB. Allows you to use older generation HID devices, including with minicomputers with only a USB connector. Adafruit 971
Retired
No product available!
Car charger G50D is a practical solution for users looking for an efficient and safe power source while traveling. Thanks to fast charging, a multi-port design, and compatibility with 12 V and 24 V voltage, it works well in both passenger and commercial vehicles. Its aesthetic and compact design makes the charger not only look good but also meet the expectations of even the most demanding users.
Retired
No product available!
No product available!
No product available!
No product available!
DIGITAL POWER SUPPLY LAMP RENOVATION VERSION - PLATES AND PROGRAMMED LAYOUT
Delivery date unknown
No product available!
GSM/GPRS + GPS module based on the RDA8955 chip. It integrates protocol stacks such as GSM/GPRS and supports the basic functions of voice calls, SMS and GPS data transmission. DFRobot TEL0134
Retired
No product available!
No product available!
Servo Extension Cable 24" Male - Female
Retired
No product available!
No product available!
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
No product available!
MEMS and environmental sensor expansion board for STM32 Nucleo