- Out-of-Stock

Pmod DPG1 is a module with a differential pressure sensor, based on the NXP MP3V5010DP system. The PCB also includes an analogue-digital ADCS7476 converter from Texas Instrument. The module allows to detect the pressure difference between two ports. The SPI interface is used for communication with the module. Digilent 410-333
Pmod DPG1 is a module with a differential pressure sensor, based on the NXP MP3V5010DP system. The ADCS7476 ADCS7476 analogue converter from Texas Instrument was also located in shallow. The module allows to detect the pressure difference between two ports. The SPI interface is used for communication with the module.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The extension cables let you locate Pmod 6" away from its host board, or use your 12-pin Pmod on a system board with only two 6-pin Pmod headers available. 240-021-2
No product available!
High-speed communication module powered by ADM582E. By communicating with the device via UART, users can take advantage of the RS485 communication protocol with speeds up to 16 Mbps. 410-310
Digital logic level shifter ideal for users who want to supply logic signals following a 3.3V CMOS standard but have an alternate logic level output that is used for other applications, such as JTAG programming. 410-320
No product available!
relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347
No product available!
The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340
Pmod HAT Adapter allows you to attach Pmod extensions to the Raspberry Pi computer. The overlay contains 3 Pmod ports and also allows access to the 40-pin PC expansion connector. Digilent 410-366
RC5 DECODER WITH SPI INTERFACE, DESCRIBED IN VERILOG LANGUAGE - PRINTED BOARD AND PROGRAMMED LAYOUT
No product available!
No product available!
No product available!
The X-NUCLEO-NFC05A1 is an NFC card reader expansion board based on the ST25R3911B. The expansion board is configured to support ISO14443A/B, ISO15693, FeliCa™ and AP2P communication
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
ROSA3D filament made of high-quality PET-G granules. 3 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G Standard Transparent
No product available!
No product available!
No product available!
ZL6ARM - development kit with LPC2138 microcontroller
No product available!
No product available!
MYIR MYS-7Z0007S-C is a single board module based on the Xilinx XC7Z007S-1CLG400C chip (Zynq-7007S). This system consists of a single-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz and Artix-7 FPGA. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
No product available!
No product available!
Pmod DPG1 is a module with a differential pressure sensor, based on the NXP MP3V5010DP system. The PCB also includes an analogue-digital ADCS7476 converter from Texas Instrument. The module allows to detect the pressure difference between two ports. The SPI interface is used for communication with the module. Digilent 410-333