- Out-of-Stock
THA012201 3DR - telemetry data set for ArduPilot with case
ID: 583728
3DR Radio is a set that allows bidirectional transmission of telemetry data, eg between the RC model (with the APM controller) and a PC. Light and small device in a set with antennas and connecting cables. Radio modules have a power of 100mW (+ 20dBm) and transmit a signal over a distance of 1km.
Description
3DR Radio is a set that allows bidirectional transmission of telemetry data between the RC model (with the APM controller: 2.5, 2.6, 2.8) and a PC. Light and small device in a set with antennas and connecting cables. The radio modules have a power of 100mW (+20 dBm) and transmit the signal to a distance of about 1.6 km.
properties
- Uses HopeRF HM-TRP radio modules (based on SiLabs Si1000 microcontroller)
- Antenna connectors: SMA
- Operating frequency: 433 MHz
- Output power: max. 100 mW (20 dBm), adjustable from 1-20 dBm
- Receiver sensitivity: up to -117 dBm
- Range about 1.6 km on the antennas of the set
- Data transfer rates: up to 250 kbps
- Interface: TTL UART (TXD lines, RXD lines)
- Serial transmission, transparent
- Can be configured using AT commands
- The base transceiver seen in the system as a virtual serial port
- Power and communication available via the microUSB connector
- Power supply for a 5V mobile transceiver
- Power consumption: 120 mA (transmission with power +20 dBm), 45 mA (reception)
- The modules can work with a bi-directional amplifier to improve the range
- Support for frequency hopping with frequency hopping (FHSS)
- Support for adaptive time multiplexing (TDM)
- Support for LBT (listening for channel occupancy before transmission starts) and AFA (selection of free frequency)
- The function of repairing incorrectly received code (possibility of improving up to 25% of errors)
- Adaptive flow control when using APM
- Open-source software
- LED indicator of the established connection
- Dimensions of the mobile / base transceiver (without antenna): 49 mm x 26 mm x 11 mm
Included
- Base transceiver with case
- Transceiver for mounting in the RC model with case
- A set of connecting cables
- Two antennas with SMA connector for 433 MHz band
583728
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Delivery date unknown
No product available!
The DE0-Nano-SoC Development Kit presents a robust hardware design platform built around the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility
Retired
No product available!
Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm
Retired
No product available!
No product available!
No product available!
FRAM memory with a capacity of 4kbit by Cypress Semiconductor, communicates via the I2C bus, the power supply voltage is in the range 2.7 - 3.6V. The system has an SOIC8 housing
Retired
No product available!
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
Retired
No product available!
Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm
Delivery date unknown
No product available!
KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO
Retired
No product available!
3DR Radio is a set that allows bidirectional transmission of telemetry data, eg between the RC model (with the APM controller) and a PC. Light and small device in a set with antennas and connecting cables. Radio modules have a power of 100mW (+ 20dBm) and transmit a signal over a distance of 1km.