

The STLINK-V3MINIE is a stand-alone debugging and programming mini probe for STM32 microcontrollers. The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board. The STLINK-V3MINIE also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART. It is a portable version easy‑to‑use debugger and programmer including STDC14 interface with its flat cable and on‑board pads for board‑to‑board (BTB) card edge connector.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board
Cable with USB type A and USB type C plugs, length 1m, white
No product available!
Cable with USB type A and USB type C plugs, length 2m, white
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board
JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)
JTAG interface for microcontrollers with ARM core
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
Versatile, low-cost debugger and programmer for 8-bit and 32-bit microcontrollers
J-Link BASE is a USB powered debug probe supporting a large number of CPU cores. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-link BASE Compact (8.19.00)
Compact programmer module for STM32 microcontrollers for soldering into a board. Supports JTAG/SWD interfaces. STLINK-V3SET has a virtual COM port and interfaces SPI, I2C, CAN, GPIO for programming via bootloader. STMicroelectronics STLINK-V3MODS
Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
No product available!
JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)
Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE