Category: STARTER KITS, PROGRAMMERS, MODULES

Board with WiFi Espressif ESP32-S2 module and 0.96" LCD display. It offers 4 MB Flash memory and 8 MB SRAM. Leads are compatible with HAT modules for Raspberry Pi Pico. Waveshare ESP32-S2-LCD-0.96-M

Starter kit from the NUCLEO series equipped with the STM32H723ZG microcontroller (1 MB Flash, Cortex-M7), with a built-in programmer-debugger ST-Link/V3, equipped with connectors compatible with Arduino. STMicroelectronics NUCLEO-H723ZG

Silicone case for the UNIHIKER computer. Provides a comfortable grip and good protection, reducing the likelihood of accidental drops and screen damage. DFRobot FIT0937

Switch module with an interlock. DFRobot DFR0423

Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262

Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG

The module with the I2C controller based on the HT16K33 system. Dedicated to 14-segment displays. It is equipped with STEMMA QT connectors. Adafruit 1910

DEV-13912

Module with a temperature and humidity sensor based on the SHT40 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4885

J-Link 6-pin Needle Adapter (8.06.16)

This sensor utilizes advanced signal processing technology by using a powerful chip (XKC-Y25-T12V) with high-speed operation capacity to achieve non-contact liquid level detection; suitable for hazardous applications: detecting toxic substances and all kinds of liquid in an airtight container under high pressure. SEN0204

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884

Silicone case for the UNIHIKER computer. Provides a comfortable grip and good protection, reducing the likelihood of accidental drops and screen damage. DFRobot FIT0936

A compact pressure and temperature module ideal for weather stations, drones, and IoT projects. It offers a measurement range of 300–1100 hPa with ±3 Pa accuracy and temperature measurement with ±1°C precision. With a built-in 3.3V regulator and logic level converter, it works with both 3V and 5V microcontrollers. STEMMA QT/Qwiic connectors make it easy to quickly connect and daisy-chain multiple sensors in a single system. Adafruit 6420

Module with a voltage level converter from 5 V to 3.3 V, intended for use in the STEMMA QT/Qwiic system. It has a built-in voltage stabilizer providing 3.3 V power supply with a current of up to 500 mA. Adafruit 5637

Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640

Grove vertical socket for surface mounting, 4-pin, pitch 2.0 mm. Set of 20 pieces. Seeed Studio 114020163