Category: STARTER KITS, PROGRAMMERS, MODULES

Pmod ESP32 is a module with the ESP-WROOM-32 system, allowing for WiFi communication, Bluetooth BLE 4.0 and Bluetooth. For communication, the SPI or UART interface is used (selected by means of the slide switch), which were output on the 12-pin Pmod connector. Digilent 410-377

A compact development board based on the RP2350 microcontroller, offering a USB Type-C connector, a Qwiic connector, and expanded memory options, including 16 MB Flash and 8 MB PSRAM. It features two ARM Cortex M33 and Hazard3 RISC-V cores, as well as support for multiple development environments, such as C/C++, MicroPython, and Arduino IDE, making it a versatile tool for a variety of projects. SparkFun DEV-24870

Module with temperature and humidity sensor TH02. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020074

MCIMX6ULL-EVK is an evaluation set from NXT with i.MX6ULL ARM Cortex-A7 900 MHz processor, 4 GB SDRAM memory and USB Host and OTG connector, Ethernet interface and SD card slot. MCIMX6ULL-EVK

Multifunctional micro:bit expansion module with built-in Li-Ion battery. The board is equipped with a two-channel DC motor driver, 9 IO pins, I2C, UART interface, buzzer, 4 RGB LEDs and a charging circuit. DFRobot MBT0005

Miniature development board with ATtiny817 microcontroller. It has analog inputs, PWM outputs and two STEMMA QT connectors. Adafruit 5233

Module with an integrated proximity and ambient light sensor based on the VCNL4040 system. It can detect obstacles in the range of 0 to 20 cm. It communicates via the I2C bus. Adafruit 4161

Module with EEPROM 24LC32 memory with a capacity of 32 kBit (4 kB). Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5146

Extension module with Li-Ion and LiPo charger dedicated to QT Py boards. It allows you to charge the batteries with a current of up to 200 mA. Adafruit 5397

The Sipeed RV Debugger Plus is a compact RISC-V BL702 programmer/debugger featuring JTAG and USB-TTL interfaces, ideal for debugging bare metal, UBOOT, and Linux environments

The module with the MCP96L01 amplifier designed to work with a thermocouple type K, J, T, N, S, E, B, or R. It has a screw connection for connecting a thermocouple and communicates via I2C. Adafruit 5165

Evaluation board with ATSAMD21E18 microcontroller (Cortex M0 +, 48 MHz, 256 KB Flash and 32 KB RAM). Equipped with a STEMMA QT connector. Adafruit 4600

Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046

A board with an RP2040 microcontroller and a radio module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and a STEMMA QT connector. Adafruit 5712

Module with a passive buzzer designed for M5Stack sets. It is equipped with a Grove connector and is controlled by a square signal. M5Stack U132

Non-contact liquid level sensor with Gravity interface. It allows you to detect the level of liquid in non-metallic containers. DFRobot SEN0485

WiFi module with ESP8266 designed to work with the Raspberry Pi Pico. It communicates via the UART interface using AT commands. Waveshare Pico-ESP8266

Module with a 4-inch touch display that uses two MCU systems (ESP32-S3 and RP2040) and supports Wi-Fi, BLE and LoRa communication. The board is equipped with USB Type C, I2C (Grove) and analog inputs interfaces and can easily connect to other peripheral devices. Seeed Studio 114993070

Flexible 4-core cable, 500 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17257

Espressif ESP32-S3 WiFi and Bluetooth LE module board. It offers 16 MB of flash memory and 2 MB of SRAM. The pinouts are compatible with the HAT modules for the Raspberry Pi Pico. Waveshare ESP32-S3-Pico-M