Category: STARTER KITS, PROGRAMMERS, MODULES

Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842

Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476

Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841

Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832

Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS160HF. STMicroelectronics X-NUCLEO-OUT08A1

GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712

Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663

Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294

Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a screw connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16295

Module with digital temperature sensor TMP102. It enables temperature measurement in the range from –40°C to 125°C with an accuracy of 0.5°C. The system communicates via the I2C interface. SparkFun SEN-16304

J-Link PRO programmer with PoE support as an alternative to USB connection. Allows you to reduce the size of cable bundles in test farms. It offers data transfer speeds of up to 4 MB/s and no limits on the number of breakpoints. It supports various operating systems, including Microsoft Windows (x86/x64), Linux (x86/x64/Arm) and macOS (x86/Apple M1). J-Link PRO PoE (8/12/28)

Module with an ambient light sensor VEML6030 with a measuring range up to 120,000 lx. It enables light measurement with 16-bit resolution. I2C communication. SparkFun SEN-15436

GPS module with 72-channel GNSS ZOE-M8Q receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART and I2C interfaces. SparkFun GPS-15193

GPS module with 72-channel GNSS SAM-M8Q receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART and I2C interfaces. SparkFun GPS-15210

Module with a capacitive touch sensor based on the CAP1203 chip. There are three touch panels on the board that can be used as separate sensors (pins CS1, CS2, CS3) or as a touch slider. I2C communication. SparkFun SEN-15344

Module with LCD display 16x2 characters with gray backlight. It is supplied with the voltage from 3.3 V to 5 V and communicates via the I2C interface. DFRobot DFR0557