Category: STARTER KITS, PROGRAMMERS, MODULES

Gigabit Ethernet transceiver with an FMC interface. Up to 1 Gbps network transfers with the host board using an FMC connector. NET-FMC can be connected any FMC(HPC) interfaces. Terasic P0481

Development kit with STM32F750N8 microcontroller (64 kB Flash, 340 kB RAM, BGA216 housing) and a built-in ST-Link / V2-1 programmer / debugger. The board also includes: ethernet, 4.3-inch TFT touch screen, audio input / output and two MEMS microphones. STMicroelectronics STM32F7508-DK

Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function

Base board compatible with Arduino. It was equipped with the ATSAMD21G18 microcontroller. It has 26 I/O lines and 14 analog inputs. SparkFun DEV-14812

Data logger based on the ATmega328 microcontroller. Data received via the I2C interface are saved on the microSD card. The module supports cards with a capacity of up to 32 GB. SparkFun DEV-15164

Module with an analog joystick that returns the X and Y position and the pressed state. The module has an ATtiny85 microcontroller on the board, which processes analog data of the joystick and sends it via the I2C interface. SparkFun COM-15168

Module with transparent OLED display. It has several display areas with different colors. I2C communication. SparkFun LCD-15079

The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.

Development board with WiFi / Bluetooth Espressif ESP32-WROVER module. The board is equipped with numerous peripheral systems, eg SD card slot, audio codec, a series of LEDs controlled by one line and a 9-axis IMU system. TTGO TAudio V1.5 ESP32-WROVER

The mainboard is an element of the microcontroller and microprocessor programming system intended for production applications. Segger Flasher ATE Main Module (5.18.01)

The RFID / NFC transponder reader module (tags) works in the PN532 chip and is compatible with Arduino. Data is available via SPI, I2C or HSU (High Speed UART). Supplied with a RFID card and key ring. ELECHOUSE NFC MODULE V3

A programming module that is an element of the programming system for microcontrollers and microprocessors, which is intended for production applications. Segger Flasher ATE Programming Module (5.18.02)

A miniature development board with ATtiny85 microcontroller, on which 6 I / O pins were derived. The module is supported by Arduino IDE. modATT85

Starter kit equipped with a STM32G071RBT6 microcontroller (128 kB Flash, Cortex-M0 +), with a built-in programmer-debugger ST-Link / v2-1, designed for prototyping devices with USB Type-C interface. STMicroelectronics STM32G071B-DISCO

The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03

NUCLEO series starter kit equipped with STM32G431KB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino Nano.

NUCLEO series starter kit equipped with STM32G431RB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

Kit for building a communication system based on QwiicBus. It contains two endpoint modules (EndPoint), an intermediary module (MidPoint) and two Ethernet cables. SparkFun KIT-17250

Adapter with galvanic isolation for STLINK-V3SET. It also allows the programmer to work with systems powered with voltages below 3.3 V. STMicroelectronics B-STLINK-ISOL

ESP32-S3 development board equipped with a 32-bit dual-core Xtensa 32-bit LX7 processor. It is equipped with a 1.14-inch IPS LCD display with a resolution of 240 x 135 pixels and a micro SD card slot. It has the format of a USB dongle with a type A connector, which makes it convenient and handy to use. Waveshare ESP32-S3-GEEK