Category: STARTER KITS, PROGRAMMERS, MODULES

A development board that combines the u-blox NINA-B306 Bluetooth module, the ISM330DHCX 6DoF IMU sensor, and the BME280 atmospheric pressure sensor. It has a built-in Qwiic connector and LiPo battery connector as well as a charger and LiPo parameters monitor. SparkFun WRL-20854

Module with a differential pressure sensor SDP31 dedicated to measuring the flow rate and air velocity. The arrangement is characterized by wide measuring range from 260 to 1260 hPa and high measurement resolution (0.01 hPa). I2C or SPI communication. SparkFun SPX-14767

The expansion module is designed to work with the micro:bit educational board. It allows you to build an electronic piano

The IO expansion module is designed to work with the micro:bit educational board. There are 20 IO pins on the board, a buzzer, audio output and voltage stabilization circuit

IO expansion module designed for use with the micro:bit educational development board. The board exposes 20 IO pins along with 3.3 V power and GND lines, enabling direct connection of sensors and electronic modules. The design includes a built-in passive buzzer and a voltage stabilization circuit allowing the module to be powered via a 6–12 V DC connector or a microUSB port

STM32 Nucleo development board for STM32 F1 series - with STM32F103RBT6 MCU, 128KB flash memory, STM, RoHS

FRDM-K22F-AGM01 is a set of development plates containing a base plate and a board with a set of 9-axis sensors with an accelerometer, a gyroscope and a magnetometer. FRDM-K22F-AGM01

A digital temperature and humidity sensor module based on the SHT41 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5776

The Flora budget starter kit contains everything you need to start an adventure with smart clothing. Included, among others motherboard, LED diodes, conductive cord, battery basket. Adafruit 1405

Starter kit with micro:bit v2. The set includes the most necessary elements needed to implement micro:bit projects: LEDs, buttons, potentiometer, servo, prototype board and a set of cables. SparkFun KIT-17362

Development kit containing the M24SR64 EEPROM chip. It can be operated by an I2C interface, a 13.56 MHz RFID reader or a phone with NFC. Version with Bluetooth module and headset

Tomasz Frenchman

Single board computer with NXP i.MX 8M processor with 2 GB of DDR4 memory, Gigabit Ethernet port, two USB 3.0 ports, HDMI output, MIPI-DSI, MIPI-CSI, WiFi, Bluetooth Low Energy and MicroSD card slot. MaaXBoard AES-MC-SBC-IMX8M-G

Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810

A development kit containing the A71CH Plug & Trust module, enabling easy and fast creation of secure IoT applications. NXP OM3710 / A71CHARD

Module with yellow LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-Y

Evaluation set FRDM-HB2001-EVM consisting of FRDM-KL25Z baseplate and extension board with DC motor controller MC33HB2001. NXP FRDM-HB2001-EVM

Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-R

A GNSS module that combines the precise u-blox ZED-F9P receiver with the NEO-D9S L-band GNSS correction data receiver. Provides high-accuracy positioning without the need for separate RTK or NTRIP corrections. SparkFun GPS-22560