Category: STARTER KITS, PROGRAMMERS, MODULES

Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640

Module with 8x8 RGB LED matrix, MY9221 LED drivers and STM32F031 microcontroller. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 105020073

Module with the LIS3DHTR 3-axis accelerometer. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020121

Module with a logarithmic digital potentiometer based on the DS1841 chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4570

Pmod MicroSD is a module with a microSD memory card reader. With the help of the module it is possible to read and write data on the microSD memory card without limiting the file system or the maximum card size. The SPI interface is used for communication. Digilent 410-380

Module with a button, LED diode and a blue cap. DFRobot DFR0029-B

The base plate is dedicated to the RP2040 Stamp module. It allows you to easily prototype devices based on RP2040. Pimoroni SP012

Module with a button and red LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-R

Module with a button and green LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-G

WiFi module with ESP8266 designed to work with the Raspberry Pi Pico. It communicates via the UART interface using AT commands. Waveshare Pico-ESP8266

MicroMod main module with iMXRT1062 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16402

Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function

8-digit, 8-segment LED display module with 16-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0646-G

The module with the transmitter and the IR receiver designed for the M5Stack sets. It is equipped with a Grove connector and communicates via a digital interface. M5Stack U002

VisionSOM module with STM32MP157A processor, 512 MB RAM memory, microSD card socket, WiFi and Bluetooth module, 0~+70C.

SLS18MP157A_650C_512R_uSD_1WB_C

The ESP32-PICO-MINI-02 development board features a dual-core 240 MHz Xtensa microcontroller, 8 MB of Flash, and 2 MB of PSRAM. It offers 2.4 GHz WiFi, Classic Bluetooth, and BLE connectivity, making it ideal for IoT projects. It features 20 GPIOs, 12-bit ADC, DAC, and PWM inputs, as well as SPI, I2C (STEMMA QT), I2S, and UART interfaces. It also includes a built-in NeoPixel RGB LED. It features low power consumption (approximately 10 µA in deep sleep), USB or 6V battery power, and compatibility with the Arduino IDE, CircuitPython, and MicroPython. Adafruit 5890

Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287

Module with a bistable button and red LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-R

Multifunctional micro:bit expansion module with built-in Li-Ion battery. The board is equipped with a two-channel DC motor driver, 9 IO pins, I2C, UART interface, buzzer, 4 RGB LEDs and a charging circuit. DFRobot MBT0005

SIMATIC LOGO! SOFT Comfort V8 from Siemens with a license for one device. It is designed to support LOGO! 8 controllers. The kit includes a DVD with software and documentation. Siemens 6ED1058-0BA08-0YA1