The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).

GPS-14414

The GY-87 module is composed of a module with MPU6050, QMC5883L and BMP180 sensors, allowing the measurement of traffic in nine axes and the measurement of atmospheric pressure. The module has a built-in 3.3 V voltage stabilizer

The 1.3 "LCD display and 168 x 144 pixel resolution is a combination of an e-ink display (e-paper) with LCD display, which is characterized by extremely low energy consumption by the eInk system and fast refresh of the LCD display. Adafruit 3502

The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A

With this smart arduino digital servo shield and Dynamixel AX series servos, It\'s quite easy for you to drive multi servos with daisy chain connection with an Arduino board  such as Arduino Uno, and build your robotic dog, hexapod with powerful servos. DRI0027

Module with FM receiver, with its help it is possible to receive radio waves broadcast in the FM band (frequency 50-115MHz). The module has been equipped with a 3,5mm jack socket, through which you can connect headphones. The module has a connector in accordance with the Grove standard. Seeed Studio 107020006

Module with a gesture sensor PAJ7620U2, which allows to recognize up to 13 gestures. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020083

Module with a magnetic sensor based on the CT10 reed switch. CT10 is a unipolar reed switch, normally open. The sensor reacts to the action of an electromagnet, permanent magnet or a combination thereof. The module has a connector in accordance with the Grove standard. Seeedstudio 101020038

Module with a dust sensor PPD42NS. The board is equipped with a Grove cable and communicates via the PWM interface. Seeed Studio 101020012

Artix-7 FPGA, 33280 Logic Cells, 5200 Slices, 90 DSP Slices, CSPBGA325, Xilinx

Zynq-7000 All Programmable SoC, Dual ARM Cortex-A9 MPCore, Artix-7 FPGA, 28K Logic Cells, 667MHz CSPBGA400, Xilinx

Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector

The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A

32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 2MB Flash memory, 216MHz clock speed, DSP with FPU, Art accelerator, SDRAM, TFT, JPEG codec, DFSDM, 144LQFP, STM, RoHS

The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435

RT8064ZQW, Synchronous Step-Down Converter, WDFN-8

RT9169-33GV, Linear Voltage Regulator 3,3V 100mA, SOT-23-3

The RFID / NFC transponder reader module (tags) works in the PN532 chip and is compatible with Arduino. Data is available via SPI, I2C or HSU (High Speed UART). Supplied with a RFID card and key ring. ELECHOUSE NFC MODULE V3