relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347

The Digilent Pmod NAV uses the LSM9DS1 3-axis accelerometer, 3-axis gyroscope, 3-axis magnetometer, plus the LPS25HB digital barometer to provide users with 10-DOF functionality. Digilent 410-326

Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473

OLD 1.3 "monochrome display with 128x64 pixel resolution with SH1106 driver The text is displayed in white, thanks to OLED technology, the power consumption is only 0.08 W. Communication via the SPI interface

Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214

Gravity I2C OLED-2864 Display is an OLED display with I2C interface with 128x64 resolution, powered by 3.3-5V. DFRobot DFR0486

This is the tiniest little LED grid, with 64 full RGB color pixels in a square. For use with Arduino and Raspberry Pi. Adafruit 3444

WRL-14147

With this smart arduino digital servo shield and Dynamixel AX series servos, It\'s quite easy for you to drive multi servos with daisy chain connection with an Arduino board  such as Arduino Uno, and build your robotic dog, hexapod with powerful servos. DRI0027

Module with FM receiver, with its help it is possible to receive radio waves broadcast in the FM band (frequency 50-115MHz). The module has been equipped with a 3,5mm jack socket, through which you can connect headphones. The module has a connector in accordance with the Grove standard. Seeed Studio 107020006

Module with a gesture sensor PAJ7620U2, which allows to recognize up to 13 gestures. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020083

The Hall sensor module allows magnetic field detection, can be used to measure angle of rotation, displacement, mechanical vibrations, etc. The module has a connector in accordance with the Grove standard. Seeed studio 101020046

Module with a magnetic sensor based on the CT10 reed switch. CT10 is a unipolar reed switch, normally open. The sensor reacts to the action of an electromagnet, permanent magnet or a combination thereof. The module has a connector in accordance with the Grove standard. Seeedstudio 101020038

KIT-14180

DFRobot SEN0153

Module with ultraviolet (UV) sensor based on the GUVA-S12D system. It allows measurement of radiation with a wavelength in the range from 240 to 370 nm. The module has a connector in accordance with the Grove standard. Seeed Studio 101020043

Integrated circuit - temperature sensor; working temperature from -40 to 100 ° C; TO92; THT, STMicroelectronics. Accuracy ± 1 ° C

Small GPS location module with L80-39 GPS chip, USB and TTL two ports,easy to be used with Raspberry Pi, Arduino, STM32 and other kind of micrcontrollers. The GPS module uses NMEA0183 communication protocol, integrated ultra-small SMA antenna connector. DFRobot TEL0119

GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501

Adapter from HDMI to VGA with microUSB power input and 3.5mm audio jack, 15cm